DKS Enterprises 1803PC 사용자 설명서
5.4 MISCELLANEOUS OPERATING INSTRUCTIONS
5.4.1 Talk Time
The talk time for directory codes 0, 00, 000, 0000 and 1, 01, 001, 0001 is factory set to 4 minutes 15
seconds and cannot be changed. These directory codes should be reserved for use with
management or emergency phone numbers that typically require longer talk times. For example, if
directory code 000 was programmed to call a management phone number, the system will allow the
full 4 minutes and 15 seconds of talk time before automatically ending the call.
seconds and cannot be changed. These directory codes should be reserved for use with
management or emergency phone numbers that typically require longer talk times. For example, if
directory code 000 was programmed to call a management phone number, the system will allow the
full 4 minutes and 15 seconds of talk time before automatically ending the call.
5.4.2 Line Sharing
More than one telephone entry system can share the same phone line provided that the units have
been programmed for multiple systems on the same line (see 3.2.2). When the unit is programmed
for multiple systems sharing the same line, it checks the phone line for 48 volts (not busy) before
attempting to place a call. If the phone line is in use, the system will emit a busy signal. If two or
more systems are sharing the same phone line, it is important that each system be programmed with
its own unique master code. When more than one system is on the same phone line, and a call is
placed from one of the systems to a resident, only the system that placed the call will respond to any
tone open numbers. Do not be concerned that all the units will activate their relay when the resident
presses the tone open number.
been programmed for multiple systems on the same line (see 3.2.2). When the unit is programmed
for multiple systems sharing the same line, it checks the phone line for 48 volts (not busy) before
attempting to place a call. If the phone line is in use, the system will emit a busy signal. If two or
more systems are sharing the same phone line, it is important that each system be programmed with
its own unique master code. When more than one system is on the same phone line, and a call is
placed from one of the systems to a resident, only the system that placed the call will respond to any
tone open numbers. Do not be concerned that all the units will activate their relay when the resident
presses the tone open number.
5.4.3 Connection to a PBX
If the telephone entry system is going to be connected to a PBX system, you may need to program
extension numbers in place of a seven-digit telephone number. To do this, enter the extension
number and fill the remaining spaces with the # key in the phone number programming step. For
example, if the PBX system uses four-digit extensions and you want to program extension 2217 as a
phone number, in step 3, section 3.5.2 press:
extension numbers in place of a seven-digit telephone number. To do this, enter the extension
number and fill the remaining spaces with the # key in the phone number programming step. For
example, if the PBX system uses four-digit extensions and you want to program extension 2217 as a
phone number, in step 3, section 3.5.2 press:
3.
2 2 1 7 # # # * (beep).
If the PBX system requires you to dial 9 to obtain an outside line, and you want to program some
outside line phone numbers in the system, program the number 9 as one of the alternate area codes.
In step 3, section 3.5.3 press:
3.
9 # # # * (beep).
Then program the outside phone number as a long distance number (3.5.4) using the area code
reference number used to program 9.
5.4.4 Areas with 10-digit Dialing
If the telephone entry system is installed in an area where the telephone company has instituted 10
digit dialing, simply program the required number of alternate area codes into the system without
preceding the area code with the number 1. If 310 was one of the area codes required, in step 3,
section 3.5.3 press:
digit dialing, simply program the required number of alternate area codes into the system without
preceding the area code with the number 1. If 310 was one of the area codes required, in step 3,
section 3.5.3 press:
3.
3 1 0 # * (beep).
Then program the outside phone number as a long distance number (3.5.4) using the area code
reference number used to program 310. Program additional area codes and phone numbers as
described in sections 3.5.3 and 3.5.4.
57