Dacor EWD 사용자 설명서

All specifications subject to change without notice.

Phone: (800) 793-0093

www.dacor.com

Document # PG02-002

Revised 01/18/12   Page 3/3

Warming

drawer

Cooktop

1 1/2" (3.8 cm)

Typical countertop

3/4” min.*

(1.9 cm)

120 Vac 

electrical

outlet

A

36" typ.

(91.4 cm)

B

C

A

Warming

drawer

Warming

drawer

B

3/4" min.*

(1.9 cm)

D

3/4" min.*

(1.9 cm)

36" typ.

(91.4 cm)

120 Vac

electrical

outlet

C

C

27"/30"/36" Dacor

single wall oven 

Warming

drawer

Warming

drawer

Toe kick

D

C

C

D

120 Vac

elect.

120 Vac

elect.

A

3/4" min.*

(1.9 cm)

Cabinet/countertop tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated

* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERWD, EWD, MRWD, MWDH, MWDV and RWDV series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout. 

The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout 

dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the 

custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below 

cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
**** Model EWD36 cannot be installed above or below another warming drawer (any type).
***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type). 

DWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

24” (61.0 cm)

ERWD27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

ERWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD24

22 1/2” (57.2 cm)

24 1/4” (61.6 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

EWD36****

34 1/2” (87.6 cm)

36 1/4” (92.1 cm)*

9 1/8” (23.2 cm)

NA

IWD24

22 1/2” (57.2 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

IWD27

25 1/2” (64.8 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

IWD30

28 1/2” (72.4 cm)

**

9 1/8” (23.2 cm)

1 1/16” (2.7 cm)

MRWD27

25 1/2” (64.8 cm)

27” (68.6 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MRWD30

28 1/2” (72.4 cm)

30” (76.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDH27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDH30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDV27

25 1/2” (64.8 cm)

27 1/4” (69.2 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

MWDV30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

OWD24*****

22 5/8” (57.5 cm)

24 1/4” (61.6 cm)*** 11 15/16” (30.3 cm) 

NA

20 1/8” (51.1 cm)

RWDV30

28 1/2” (72.4 cm)

30 1/4” (76.8 cm)*

9 1/8” (23.2 cm)

1 1/4” (3.2 cm)*

24” (61.0 cm)

•  Observe all governing codes and ordinances 

during planning and installation. Contact your 

local building department for further information. 

•  This appliance must be installed in accordance 

with the accompanying installation instructions.

Mounting platform must be 3/4" (1.9 cm) thick 

and support 100 lbs.