Wr Rademacher DuoFern 35000462 Multi-purpose dimming actuator Flush mount 1-channel Max. range (open field) 100 m 35000462 데이터 시트

제품 코드

35000462

230V / 50 Hz

L‘

5. Installation

During both installation and dismantling of the

DuoFern Universal Dimmactuator (fm) there is a risk of

fatal electric shocks.
Observe the safety instructions for electrical connection in

chapter 7.

The DuoFern Universal Dimmactuator (fm) is intended for flush mounting.

We recommend using a deep box.
You require for installation a 58 mm flush-mounted box.
NOTE

In order to ensure optimal operation, the DuoFern Universal Dimmactuator

(fm) should not be installed on a metallic base or near metal objects.

5.1 Installation procedure
1. Switch off the mains (at the fuse box or consumer unit).
2. Electrical connection in accordance with chapter 7. / 7.1.
3. Reconnect the mains power.
4. Register the DuoFern Universal Dimmactuator (fm) in the DuoFern

radio network, see chapter 8.

5. Switch off the mains voltage again after registration has

been successfully completed.

6. Insert the DuoFern Universal Dimmactuator (fm) in the flush-

mounted box and lay the connecting cables in the box.
ATTENTION

◆

Avoid bending the antenna too far as it could otherwise break off.

7. Mount the cover plate on the flush-mounted box.
8. Reconnect the mains power.
9. The DuoFern Universal Dimmactuator (fm) automatically detects the

connected load.

The DuoFern Universal Dimmactuator (fm) is then ready for operation after

approx. 15 seconds.

13. Warranty conditions

RADEMACHER Geräte-Elektronik GmbH provides a 24-month warranty for new systems that
have been installed in compliance with the installation instructions. All construction faults,
material defects and manufacturing defects are covered by the warranty.

The following are not covered by the warranty:

◆

Incorrect fitting or installation

◆

Non-observance of the installation and operating instructions

◆

Improper operation or wear and tear

◆

External influences, such as impacts, knocks or weathering

◆

Repairs and modifications by third party, unauthorised persons

◆

Use of unsuitable accessories

◆

Damage caused by unacceptable excess voltage (e.g. stroke of lightning)

◆

Operational malfunctions caused by radio frequency overlapping and other such
radio interference

RADEMACHER shall remedy any defects, which occur within the warranty period free of
charge either by repair or by replacement of the affected parts or by supply of a new
replacement unit or one to the same value. There is no general extension of the original
warranty period by delivery of a replacement or by repair as per the terms of the warranty.

t t

o t

ica

l m

ifi

tio

, m

isp

rin

rs.

Ill

tra

tio

t b

RADEMACHER
Geräte-Elektronik GmbH & Co. KG
Buschkamp 7
46414 Rhede (Germany)
info@rademacher.de
www.rademacher.de
Service:
Hotline 01805 933-171*
Fax +49 2872 933-253
service@rademacher.de

11. Technical Data

Supply voltage:

230 V / 50 Hz

Standby consumption:

< 0,5 W

Minimum load:

25 W

Maximum load:

250 W

Transmitting power:

10 mW

Range in a building:

approx. 30 m (depending on

construction)

Range outside:

approx. 100 m

Transmission frequency:

434.5 MHz

Maximum no. of DuoFern transmitters: 20
Permissible ambient temperature:

+ 5 °C to + 40°C

Dimensions (Diameter / Hight):

48 mm / 24 mm

Dimming of:

- Ohmic loads (e. g. bulbs)

- Leading-edge phase control *

- Trailing-edge phase control *

* transformer

9. Logging on and off per radio code

You can control the DuoFern Universal Dimmactuator (fm) directly using

the radio code in order, for example, to be able to connect further DuoFern

transmitters to the Universal Dimmactuator (fm) after installation. You will

find the radio code on the enclosed label and on the rear side of the Universal

Dimmactuator (fm).
1. Enter the Universal Dimmactuator (fm)’s radio code in menu

“2.2. Radio code” of the DuoFern central operating unit.

2. Activate and confirm connect / disconnect mode for the

Universal Dimmactuator (fm) on the DuoFern central operating

unit.

3. Call up menu “2. Radio Settings”.
4. Activate function “2.1 Connect/disconnect” on the DuoFern

central operating unit.

5. Connect the Universal Dimmactuator (fm) with the DuoFern

central operating unit or disconnect from the DuoFern central

operating unit.

6. Assign the Universal Dimmactuator (fm) to the respective

groups / member numbers and names.

A more detailed description can be found in the DuoFern central operat-

ing unit’s operating manual.

10. Deleting all settings (Reset)

1. Press the Disconnect button until the indicator LED lights up

continuously red.

2. All of the settings are deleted and the logged in DuoFern trans-

mitters are automatically logged off.

3. All of the settings will be reset to the factory settings. Sub-

sequently, the DuoFern Universal Dimmactuator (fm) will be

reset to its delivery setting.

8. Logging DuoFern transmitters on/off

You must assign every required DuoFern transmitter to the DuoFern Universal

Dimmactuator (fm) in order that the Universal Dimmactuator (fm) can be

controlled with a DuoFern transmitter. You can assign max. 20 DuoFern

transmitters, e. g. DuoFern manual transmitter Standard to the Universal

Dimmactuator (fm).
1. Switch the desired DuoFern transmitter to connect-/ disconnect

mode (please refer to the corresponding operating instructions).

2. Press the “Connect (log-on)” or “Disconnect (log-off)” button

on the upper side of the housing.

3. The Universal Dimmactuator (fm) then transmits either a

log-on or log-off signal. Registering mode remains active for

120 seconds.

4. If registration is successful, the indicator light will light up

green constantly.

5. Register the next DuoFern transmitter. In order to do so, repeat

steps 1 to 3, or else terminate Logging on/off.
NOTE

The indicator LED lights up red if the registration process fails, for

example if:

◆

20 DuoFern transmitters have already been registered.

◆

A unsuitable device (e. g. other DuoFern actuator) is registered.

◆

An attempt is made to log-off a DuoFern transmitter that is not

logged-on.

7.2 Connection terminals

7.1 Wiring diagram

Consumer

DuoFern

Universal

Dimmactuator (fm)

Incorrect wiring may lead to short-circuits and

destruction of the device.

◆

Observe the sequence of connector pin assignments in the

wiring diagram and on the type plate.

Connection instructions for local operation
You can use a switch to enable local control via the 230 V control input. The

maximum permissible cable length amounts to 10 m.
IMPORTANT

When the control input is used, the switch and the actuator must be con-

nected to the same phase (L). If the control input is not used, then nothing

may be connected to the terminal!

7. Electrical connection

Safety instructions

There is a risk of fatal electric shocks.

The electrical connection and all work on electrical systems

must only be carried out by a qualified electrician in accordance

with the connection instructions in these operating instructions.

◆

Carry out all installation and connection work only in an

isolated, deenergised state.

◆

Disconnect all phases of the mains power supply cable and

secure it to prevent reconnection.

◆

Check that the system is dead.

◆

Prior to connecting, compare the information about

voltage/frequency on the device with those of the local

electrical grid operator.

7. Electrical connection

6. Dismantling

1. Switch off the mains (at the fuse box or consumer unit).
2. Open the flush-mounted box.
3. Disconnect the DuoFern Universal Dimmactuator (fm) and

remove it from the flush-mounted box..

* 14 ct/minute on a German landline

operated by DT AG / Mobile charges

max. 42 cents/minute (Germany only)

12. CE Mark and EC Conformity

The DuoFern Universal Dimmactuator (fm), (Item no. 3500 04 64) complies
with the requirements of the current European and national directives.

1999/5/EC

R&TTE directive

2006/95/EC

Low voltage directive

2004/108/EC EMC directive

Conformity has been verified. The corresponding declarations and documen-
tation are available on file at the manufacturer’s premises.