Enterasys Networks MATRIX 7H4385-49 사용자 설명서
Preparing to Install into a Matrix E7, N1, N3, N5, or N7 Chassis
DFE-Platinum Series Hardware Installation Guide 3-7
Preparing to Install into a Matrix E7, N1, N3, N5, or N7 Chassis
To install any module into the Matrix E7
chassis, refer to “
” on page 3‐3 to familiarize yourself with the FTM1 and FTM2 backplane
connections and the module hardware installation rules. Then proceed as follows to
prepare the DFE module for installation.
prepare the DFE module for installation.
To install a DFE module into a Matrix E7, Matrix N1, Matrix N3, Matrix N5,
or
Matrix N7
chassis, proceed as follows to prepare the module for installation.
1.
Remove the blank panel covering the slot in which the module will be installed. All
other slots must remain covered to ensure proper airflow for cooling. (Save the blank
plate in the event you need to remove the module.)
other slots must remain covered to ensure proper airflow for cooling. (Save the blank
plate in the event you need to remove the module.)
2.
Remove the module from the shipping box. (Save the box and packing materials in
the event the module needs to be reshipped.)
the event the module needs to be reshipped.)
3.
Locate the antistatic wrist strap shipped with the chassis. Attach the antistatic wrist
strap to your wrist and plug the cable from the antistatic wrist strap into the ESD
grounding receptacle at the upper right corner of the chassis.
strap to your wrist and plug the cable from the antistatic wrist strap into the ESD
grounding receptacle at the upper right corner of the chassis.
4.
Remove the module from the plastic bag. (Save the bag in the event the module must
be reshipped.) Observe all precautions to prevent damage from Electrostatic
Discharge (ESD).
be reshipped.) Observe all precautions to prevent damage from Electrostatic
Discharge (ESD).
Caution: Failure to observe static safety precautions could cause damage to the module.
Follow static safety handling rules and wear the antistatic wrist strap.
Follow static safety handling rules and wear the antistatic wrist strap.
Do not cut the non-conductive bag to remove the module. Sharp objects contacting the
board or components can cause damage.
board or components can cause damage.
Precaución: Si no toma las medidas de seguridad necesarias para evitar descargas de
electricidad estática, es posible que el módulo se dañe. Siga los consejos de seguridad
para la manipulación del producto y no olvide utilizar la pulsera antiestática.
electricidad estática, es posible que el módulo se dañe. Siga los consejos de seguridad
para la manipulación del producto y no olvide utilizar la pulsera antiestática.
No corte la bolsa antiestática para sacar el módulo. Tenga en cuenta que si algún objeto
cortante entra en contacto con la placa o con los componentes, éstos podrían dañarse.
cortante entra en contacto con la placa o con los componentes, éstos podrían dañarse.
Warning: Install this module in a Matrix E7, N1, N3, N5, or N7 chassis that has been
installed in a Restricted Access Location only. Access to the equipment by users must be
restricted through the use of a tool or lock and key or other means of security and is
controlled by the authority responsible for the location.
installed in a Restricted Access Location only. Access to the equipment by users must be
restricted through the use of a tool or lock and key or other means of security and is
controlled by the authority responsible for the location.
Advertencia: Instalar este modulo en un Matrix E7, N1, N3, N5, o N7 que ha sido
localizado en un lugar de Acceso Restringido. Aceso al equipo debe ser restringido por el
responsable del sitio.
localizado en un lugar de Acceso Restringido. Aceso al equipo debe ser restringido por el
responsable del sitio.
Warnhinweis: Installieren Sie dieses Modul nur in einem E7, N1, N3, N5, oder N7
Chassis, wenn sich diese in einer zugangsgeschützten Umgebung befinden. Der Bereich
zu den Komponenten sollte durch ein Schloß, einen Schlüssel oder sonstigen
Sicherungen geschützt und durch einen Verantwortlichen kontrolliert werden.
Chassis, wenn sich diese in einer zugangsgeschützten Umgebung befinden. Der Bereich
zu den Komponenten sollte durch ein Schloß, einen Schlüssel oder sonstigen
Sicherungen geschützt und durch einen Verantwortlichen kontrolliert werden.