Electrolux - Gibson 315541 전단
INSTALLATION INSTRUCTIONS
PART #315541
WHEN INSTALLING THIS EXHAUST SYSTM, MAKE SURE TO USE PROPER SAFETY
PRECAUTIONS. USE JACK STANDS WHEN UNDER THE TRUCK, BLOCK TIRES AND
USE SAFETY GLASSES AND GLOVES. DO NOT WORK WITH HOT PIPES!
PRECAUTIONS. USE JACK STANDS WHEN UNDER THE TRUCK, BLOCK TIRES AND
USE SAFETY GLASSES AND GLOVES. DO NOT WORK WITH HOT PIPES!
SUGGESTED TOOLS
½”, 9/16”, 15MM SOCKET & WRENCH, WD-40, JACK STAND, HACKSAW
TO REMOVE STOCK EXHAUST CUT
OFF YOUR STOCK SYSTEM JUST IN
FRONT OF THE MUFFLER AFTER THE
WELD, LEAVE ALL RUBBER
GROMMETS ON THE HANGERS. USE
WD-40 TO AID IN THE REMOVAL OF
EXHAUST AND HANGERS.
OFF YOUR STOCK SYSTEM JUST IN
FRONT OF THE MUFFLER AFTER THE
WELD, LEAVE ALL RUBBER
GROMMETS ON THE HANGERS. USE
WD-40 TO AID IN THE REMOVAL OF
EXHAUST AND HANGERS.
INSTALL HEAD PIPE # A ON TO
YOUR EXISTING STOCK FRONT
PIPE AND SECURE WITH CLAMP
# F. DO NOT TIGHTEN.
YOUR EXISTING STOCK FRONT
PIPE AND SECURE WITH CLAMP
# F. DO NOT TIGHTEN.
INSTALL MUFFLER # B ONTO
HEAD PIPE #A 1-1/2” TO 2”
WITH THE LOUVERS FACING
TOWARDS THE CONVERTER.
USE A JACK STAND TO
SUPPORT THE MUFFLER. USE
CLAMP #G SECURE THE
MUFFLER TO THE HEAD PIPE.
DO NOT TIGHTEN. MUFFLER
INLET IS LOOKING INTO THE
LOUVERS.
HEAD PIPE #A 1-1/2” TO 2”
WITH THE LOUVERS FACING
TOWARDS THE CONVERTER.
USE A JACK STAND TO
SUPPORT THE MUFFLER. USE
CLAMP #G SECURE THE
MUFFLER TO THE HEAD PIPE.
DO NOT TIGHTEN. MUFFLER
INLET IS LOOKING INTO THE
LOUVERS.
INSTALL THE OVERAXLE
TAIL PIPE #C INTO THE
MUFFLER 1 ½”-2” . SECURE TO
MUFFLER USING CLAMP #G.
DO NOT TIGHTEN.
TAIL PIPE #C INTO THE
MUFFLER 1 ½”-2” . SECURE TO
MUFFLER USING CLAMP #G.
DO NOT TIGHTEN.
INSTALL STAINLESS STEEL
TIP. CLAMP DOWN. WHEN
YOU HAVE EVERYTHING IN
PLACE, FIRMLY TIGHTEN
ALL BOLTS AND CLAMP
DOWN SECURELY. TO CLEAN
STAINLESS STEEL TIPS
USE ANY SAINLESS STEEL
CLEANER AND SCOTCH
BRITE PAD.
TIP. CLAMP DOWN. WHEN
YOU HAVE EVERYTHING IN
PLACE, FIRMLY TIGHTEN
ALL BOLTS AND CLAMP
DOWN SECURELY. TO CLEAN
STAINLESS STEEL TIPS
USE ANY SAINLESS STEEL
CLEANER AND SCOTCH
BRITE PAD.
“MAKE SURE YOU HAVE A MINIMUM OF A 1” CLEARANCE ON ALL PIPES FROM
ALL RUBBER BRAKE LINES, TIRES, SHOCKS, FUEL LINES, ETC.”
TORQUE CLAMPS TO 100 – 150 FT. LBS.
INSTALL BAND CLAMP #H
ONTO MUFFLER. INSERT
WELDED HANGER INTO
RUBBER GROMMET. TIGHTEN
BAND CLAMP USING
HARDWARE KIT #I.
ONTO MUFFLER. INSERT
WELDED HANGER INTO
RUBBER GROMMET. TIGHTEN
BAND CLAMP USING
HARDWARE KIT #I.
INSTALL THE TURNOUT PIPE
#D ON TO THE TAILPIPE.
SECURE TOGETHER WITH
CLAMP #G. DO NOT TIGHTEN.
ROLL THE EXIT PIPE UNTIL
IT IS AT THE CORRECT
ANGLE FOR YOUR TRUCK.
INSERT WELDED HANGER
INTO GROMMET.
#D ON TO THE TAILPIPE.
SECURE TOGETHER WITH
CLAMP #G. DO NOT TIGHTEN.
ROLL THE EXIT PIPE UNTIL
IT IS AT THE CORRECT
ANGLE FOR YOUR TRUCK.
INSERT WELDED HANGER
INTO GROMMET.
CUT HERE