Denon DN-X1500 사용자 설명서

ENGLISH

Sampler playback

SAMPLER

Select the source of Sampler

• Turn the ASSIGN switch

y in the SAMPLER

part to select the desired source.

Setting B point / Stop recording

When the B button

o is pushed during

recording, the B point is set.
• Recording continues for approximately 8

seconds without stopping after set B point.

• If the B point is not set, recording end point

set as B point automatically.

Record in Sampler

When the A button

i is pushed, the sound of

the selected source is recorded to Sampler
memory up to 8 seconds.
• The A button

i flashes after recording starts.

• When the recording is completed, B button

o lights up.

-1

Select Sampler play mode

You can select play mode for Sampler when
Sampler playback stop.

Loop (default):

Sampler playback continues with looping.

Single:

Sampler playback stops at B point.

Stutter:

Sampler is played while the A button

i is

pressed and held down.

Loop + Reverse:

Reverse Sampler playback continues with
looping.

Single + Reverse:

Reverse Sampler stops at A point.

Stutter + Reverse:

Reverse Sampler is played while the A
button

i is pressed and held down.

Exit B:

Sampler playback continues over B point
up to recording length.

Play Sampler sound

• Playback of the Sampler sound starts when

the A button

i is pushed after recording has

completed.

• To stop the Sampler sound, push the MODE

knob

• When the CROSSFADER ASSIGN switch

in the SAMPLER part is set A or B, you can
perform the Sampler Fader Start by the
Crossfader

!8. See page 10.

Moving Sampler B point

• When the B button

o is pushed during

Sampler playback, the B point moves to the
point at which the button was pushed, and
Loop playback from point A starts.

Setting the Sampler sound level

The sound level (volume) can be set for
Sampler.
• To select “S_Level” turn the MODE knob

and push.

• Turn the MODE knob

u and select between

“–14 dB” and “+6 dB”.

Clearing the Sampler data

• While pressing the MODE knob

u, push the

A button

i to clear the Sampler.

Sampler A/B Trim

Select A-B Trim mode

• To select “A/BTrim” turn the MODE knob

and push.

Select A point (in A-B Trim)

• Push the A button

• The A button

i illumination flashes and Loop

playback starts.

Select B point (in A-B Trim)

• Select the A-B Trim mode and push the B

button

• The B button

o illumination flashes.

Trim A point

• Turn the MODE knob

u. You can move the A

point.

Save the A point

• Push the MODE knob

u to save new the A

point.

Trim B point

• Turn the MODE knob

u. You can move the B

point.

PFL (Pre Fader Level)

1. Press the SPLIT CUE button

@4.

2. Press the CUE button

!6 that you wish to monitor

1~ 4 (make sure your source is playing).

3. Turn the GAIN control

#5 until the meters peak at

the 0 dB level.

4. Perform your mix using the Crossfader

!8 or Ch.

Fader

!9 at your desire.

NOTES:
• For proper operation, your channel levels should

always be set to or left on reference line 8.

• This adjustment can be made even if the Ch. Fader

is set to zero level.

Setting the Sampler pitch

The sound pitch can be set for Sampler.
• To select “S_Pitch” turn the MODE knob

and push.

• Turn the MODE knob

u and select between

“–100 %” and “+100 %”.

To select Loop/Reverse mode, turn the MODE
knob

u then push after recording and before

playing.
q Play mode:

• To select “P_Mode” turn the MODE knob

u and push.

• Turn the MODE knob

u and select

“Loop”, “Exit B”, “Single” or “Stutter”.

w Play direction:

• To select “DirMode” turn the MODE knob

u and push.

• Turn the MODE knob

u and select

“Forward” or “Reverse”.

-2

Monitoring the Sampler data
(SAMPLER CUE)

• When the SAMPLER CUE button

!6 is

pressed, you can check the Sampler data.

NOTE:

When the SAMPLER CUE button is lit, the
Sampler sound is not output into the
Crossfader or MASTER OUT.

Save the B point

• Push the MODE knob

u to save new the B

point.