Delta Tau GEO BRICK LV 참조 매뉴얼
Turbo PMAC/PMAC2 Software Reference
Turbo PMAC On-line Command Specification
318
DISABLE PLC
Function:
Disable specified PLC programs.
Scope:
Global
Syntax:
DISABLE PLC {constant}[,{constant}]
DIS PLC {constant}[,{constant}]
DISABLE PLC {constant}..{constant}
DIS PLC {constant}..{constant}
where
{constant} is an integer from 0 to 31, representing the program number
This command causes Turbo PMAC to disable (stop executing) the specified uncompiled PLC program
or programs. Execution can subsequently be resumed at the top of the program with the ENABLE PLC
command. If it is desired to restart execution at the stopped point, execution should be stopped with the
PAUSE PLC command, and restarted with the RESUME PLC command
or programs. Execution can subsequently be resumed at the top of the program with the ENABLE PLC
command. If it is desired to restart execution at the stopped point, execution should be stopped with the
PAUSE PLC command, and restarted with the RESUME PLC command
The on-line DISABLE PLC command can only suspend execution of a PLC program at the end of a
scan, which is either the end of the program, or after an ENDWHILE statement in the program. PLC
programs are specified by number, and may be specified in a command singularly, in a list (separated by
commas), or in a range of consecutively numbered programs. PLC programs can be re-enabled by using
the ENABLE PLC command. If a motion or PLC program buffer is open when this command is sent to
Turbo PMAC, the command will be entered into that buffer for later execution.
scan, which is either the end of the program, or after an ENDWHILE statement in the program. PLC
programs are specified by number, and may be specified in a command singularly, in a list (separated by
commas), or in a range of consecutively numbered programs. PLC programs can be re-enabled by using
the ENABLE PLC command. If a motion or PLC program buffer is open when this command is sent to
Turbo PMAC, the command will be entered into that buffer for later execution.
Example:
DISABLE PLC 1
DIS PLC 5
DIS PLC 3,4,7
DISABLE PLC 0..31
DIS PLC 5
DIS PLC 3,4,7
DISABLE PLC 0..31
See Also:
I-variable I5
On-line commands ENABLE PLC, OPEN PLC, DISABLE PLCC, ENABLE PLCC, <CONTROL-D>.
Program commands DISABLE PLC, ENABLE PLC, DISABLE PLCC, ENABLE PLCC
I-variable I5
On-line commands ENABLE PLC, OPEN PLC, DISABLE PLCC, ENABLE PLCC, <CONTROL-D>.
Program commands DISABLE PLC, ENABLE PLC, DISABLE PLCC, ENABLE PLCC
DISABLE PLCC
Function:
Disable compiled PLC programs.
Scope:
Global
Syntax:
DISABLE PLCC {constant}[,{constant}]
DIS PLCC {constant}[,{constant}]
PLCC {constant}..{constant}
DIS PLCC {constant}..{constant}
where:
{constant} is an integer from 0 to 31, representing the compiled PLC program number
This command causes Turbo PMAC to disable (stop executing) the specified compiled PLC program or
programs. Compiled PLC programs are specified by number, and may be specified in a command
singularly, in a list (separated by commas), or in a range of consecutively numbered programs. PLC
programs can be re-enabled by using the ENABLE PLCC command.
programs. Compiled PLC programs are specified by number, and may be specified in a command
singularly, in a list (separated by commas), or in a range of consecutively numbered programs. PLC
programs can be re-enabled by using the ENABLE PLCC command.
If a motion or PLC program buffer is open when this command is sent to Turbo PMAC, the command
will be entered into that buffer for later execution.
will be entered into that buffer for later execution.