사용자 설명서차례Important Safety Instructions7Save These Instructions.71.0 Introduction8Table 1 Option Requirements81.1 Opening the UPStation S39Figure 1 UPStation S3 Front and Option Area Access91.2 Installing the Mounting Bracket10Figure 2 Mounting Bracket Installation10Figure 3 Option Guides11Figure 4 Cable Track111.3 Closing and Restarting the UPStation S3122.0 Power Supply132.1 Introduction132.2 Installing the Power Supply Option132.2.1 Connect the Power Supply to an UPStation S3 Option Board13Figure 5 Mounting the Power Supply Option13Figure 6 Power Supply Option and Power Supply Terminal Block14Figure 7 UPS (Output) Terminal Block Cable Routing and Wiring Connections152.2.2 Output Terminal Block Wiring Connections163.0 Remote Status Panel173.1 Introduction173.2 Installing the Remote Status Panel183.2.1 Installation Instructions18Figure 8 Wiring Connections18Table 2 Remote Status Panel Customer Connections (Factory Setup)193.3 Operating Instructions203.3.1 The Remote Status Panel203.3.2 The Lamp Test/Reset Pushbutton203.3.3 Audio Reset Pushbutton204.0 Programmable Relay Board214.1 Introduction214.2 Installing the Programmable Relay Option214.2.1 Mounting Instructions214.2.2 Internal Wiring Connections21Figure 9 Programmable Relay Board Internal Wiring Connections224.2.3 External Connections23Table 3 Remote Status Panel Customer Connections (Factory Setup)23Table 4 Wiring Connections, AS/400 Interface Option24Table 5 User Programmable Customer Connections254.3 Operating Instructions264.3.1 Configure the Relay Contacts26Table 6 Group Event Options284.3.2 Review the Existing Contact Assignments294.3.3 Reset the Contacts to Factory Default Settings30Table 7 IBM AS/400® Contact Definitions30Table 8 Liebert Remote Status Panel Contact Definitions305.0 Input Contact Isolator315.1 Introduction315.2 Installing the Input Contact Isolator31Figure 10 Input Contact Isolator Power Supply Terminal Block Wiring32Figure 11 Input Contact Isolator Connections to Main Controller Board (Direct)33Figure 12 Input Contact Isolator Connection to Main Controller Board (Indirect)34Figure 13 Customer Connections345.3 Operating Instructions355.3.1 Configure Input Contacts355.3.2 Review the Existing Contact Assignments366.0 DC Ground Fault Detector376.1 Introduction376.2 Installing the DC Ground Fault Detector37Figure 14 DC Ground Fault Cable Routing38Figure 15 DC Ground Fault Wiring Connections39Table 9 Program Jumper Selection406.3 Operating Instructions407.0 SNMP for Ethernet and Token Ring Systems417.1 Introduction417.2 Installation417.2.1 Installing the SNMP Hardware41Figure 16 SNMP Option Wiring Connections - Ethernet and Token Ring417.3 Configuring the SNMP Agent43Table 10 Ethernet Configuration Menu43Table 11 Token Ring Configuration Menu43Table 12 Communities Configuration Menu44Table 13 Trap Communities Configuration Menu458.0 Internal Modem468.1 Introduction468.2 Installing the Internal Modem Option478.2.1 Mounting Instructions47Figure 17 Power Connections to the Modem Board478.3 Operating Instructions488.3.1 Configuring the Modem Mode and Call #2 Settings488.3.2 Using the Modem for Incoming Calls49Configuring the Modem to Accept Incoming Calls49Table 14 Modem Communication Parameters49Receiving Incoming Calls498.3.3 Using the Modem for Outgoing Calls50Table 15 Modem Dial-Out Events50Entering and Editing Phone Numbers50Table 16 Telephone Number Characters52Calling a Remote Modem53Calling a Pager53Calling a Dumb Terminal549.0 Appendix A - UPStation S3 Options Testing Procedures559.1 Power Supply Option Test Procedure55Figure 18 Load Resistor Connection559.2 Programmable Relay Board Option Test Procedure569.3 Remote Status Panel Option Test Procedure57Figure 19 Remote Status Panel to Programmable Relay - RSP Test Connections579.4 Input Contact Isolator Option Test Procedure58Figure 20 Input Contacts589.5 DC Ground Fault Detector Option Test Procedure59Figure 21 DC Ground Fault Detector Test Wiring599.6 Modem Option Test Procedure60크기: 950킬로바이트페이지: 61Language: Tiếng việt매뉴얼 열기