Stow MS-40H Manual Do Utilizador
PAGE 18 — STOW MS-40H HYDRAULIC MIXER— PARTS & OPERATION MANUAL — REV. #1 (05/17/02)
MS-40H HYDRAULIC MIXER — MAINTENANCE
WHEEL BEARINGS
After every 3 months of operation, remove the hub dust cap and
inspect the wheel bearings. Once a year, or when required,
disassemble the wheel hubs remove the old grease and repack
the bearings forcing grease between rollers, cone and cage
with a good grade of high speed wheel bearing grease (never
use grease heavier than 265 A.S.T.M. penetration (“No. 2.”) Fill
the wheel hub with grease to the inside diameter of the outer
races and also fill the hub grease cap.
inspect the wheel bearings. Once a year, or when required,
disassemble the wheel hubs remove the old grease and repack
the bearings forcing grease between rollers, cone and cage
with a good grade of high speed wheel bearing grease (never
use grease heavier than 265 A.S.T.M. penetration (“No. 2.”) Fill
the wheel hub with grease to the inside diameter of the outer
races and also fill the hub grease cap.
Reassemble the hub and mount the wheel. Then tighten the
adjusting nut, at the same time turn the wheel in both directions,
until there is a slight bind to be sure all the bearing surfaces are
in contact.
adjusting nut, at the same time turn the wheel in both directions,
until there is a slight bind to be sure all the bearing surfaces are
in contact.
Then back-off the adjusting nut 1/6 to 1/4 turn or to the nearest
locking hole or sufficiently to allow the wheel to rotate freely
within limits of .001" to .010" end play. Lock the nut at this position.
Install the cotter pin and dust cap, and tighten all hardware.
locking hole or sufficiently to allow the wheel to rotate freely
within limits of .001" to .010" end play. Lock the nut at this position.
Install the cotter pin and dust cap, and tighten all hardware.
SHAFT SEALS
CAUTION:
IMPORTANT -DRUM HEAD SEAL CARE
Grease seals every 40 hours of operation using
any grade #1 lithium base grease. Apply
any grade #1 lithium base grease. Apply
grease until visible inside of mixing tub (over
grease). This will purge seal system of
grease). This will purge seal system of
contamination.
PADDLE SHAFT BEARINGS
The paddle shafts in theSTOWMS-40H hydraulic mixers rotate
in sealed ball bearings, which require no additional lubrication
as they are packed and sealed at the factory.
in sealed ball bearings, which require no additional lubrication
as they are packed and sealed at the factory.
There is, on each end of the mixing drum, an zerk grease fitting.
Oil these fittings two or three times each week as they lubricate
the dumping mechanism of the mixing drum.
Oil these fittings two or three times each week as they lubricate
the dumping mechanism of the mixing drum.
CAUTION:
■
Failure to lubricate the zerk grease fittings
two or three times a week will cause the
dumping mechanism to stiffen, making the
mixer hard to dump.
dumping mechanism to stiffen, making the
mixer hard to dump.
BEARING BRACKET
Grease the bearing bracket every month.
CLEANING
Always disconnect the spark plug wire before cleaning the inside
of the drum.
of the drum.
Never pour or spray water over the gasoline engine or electric
motor.
motor.
For consistent performance, long life and high quality mixing,
thoroughly clean the mixer inside and out at the end of each
day’s operation. To prevent lumps of dried mortar from forming
and contamination of future batches, do not allow a buildup of
materials to form on the blades or anywhere inside the drum.
thoroughly clean the mixer inside and out at the end of each
day’s operation. To prevent lumps of dried mortar from forming
and contamination of future batches, do not allow a buildup of
materials to form on the blades or anywhere inside the drum.