Roland 04672434 Manual Do Utilizador
153
SYSTEM Chapter 8 Parameter Guide
Chapter 8
BPM
*
The parameters enabled (SYSTEM BPM, BPM) change according to
the BPM MODE settings.
When they are disabled, the value < > is given.
the BPM MODE settings.
When they are disabled, the value < > is given.
V-LINK
CLIP
ASSIGN 1–2
Parameter/
Range
Range
Explanation
BPM MODE
SYSTEM
The values set in the SYSTEM parameter
SYSTEM BPM is enabled.
SYSTEM BPM is enabled.
PATCH
The values set in BPM for each patch is en-
abled.
abled.
SYSTEM BPM
40–250
Adjust the BPM value for the entire system.
* BPM (beats per minute) indicates the number of quarter note beats that
occur each minute.
* When
INTERNAL, sending a MIDI clock signal from an external MIDI
instrument synchronizes the VB-99 to the MIDI clock signal that was
sent. To enable the BPM setting, set this to INTERNAL.
instrument synchronizes the VB-99 to the MIDI clock signal that was
sent. To enable the BPM setting, set this to INTERNAL.
Control with the SYSTEM BPM
You can tap input the SYSTEM BPM with [F2].
V-LINK PATCH
Parameter/
Range
Range
Explanation
This sets the Program Change messages transmitted when patches
are switched.
You can set different Program Changes in Channel A and Channel
B. The clips (video images) on the receiving device are switched by
these Program Change messages.
are switched.
You can set different Program Changes in Channel A and Channel
B. The clips (video images) on the receiving device are switched by
these Program Change messages.
A ch/B ch PALETTE
OFF, 1–32
This sets the Bank Select number (CC#0,
#32).
#32).
A ch/B ch CLIP
OFF, 1–32
This sets the Program Change numbers.
Parameter/
Range
Range
Explanation
These settings are necessary for controlling video using the bass’s
performance data and messages from the VB-99’s controllers.
You can make up to two types of settings.
performance data and messages from the VB-99’s controllers.
You can make up to two types of settings.
SOURCE
OFF
The V-LINK function is not assigned.
BEND
Pitch bend messages
VELO
Velocity messages
GK VOL
GK-3B GK volume knob
GK S1
GK-3B DOWN/S1 switch
GK S2
GK-3B UP/S2 switch
CTL1
Control button1
CTL2
Control button2
EXP PEDAL
Expression pedal connected to the EXP
PEDAL jack
PEDAL jack
CTL3
Footswitch connected to the CTL3,4 jack
(jack tip)
(jack tip)
CTL4
Footswitch connected to the CTL3,4 jack
(jack ring)
(jack ring)
D BEAM V
D BEAM vertical movements
D BEAM H
D BEAM horizontal movements
RIBBON
RIBBON CONTROLLER
FC-300 EXP1
FC-300 expression pedal1
FC-300 EXPSW1
FC-300 expression pedal switch1
FC-300 EXP2
FC-300 expression pedal2
FC-300 EXPSW2
FC-300 expression pedal switch2
FC-300 CTL1
FC-300 control pedal1
FC-300 CTL2
FC-300 control pedal2
FC-300 E3/C3
FC-300 external expression pedal3/external
footswitch3
footswitch3
FC-300 CTL4
FC-300 external footswitch4
FC-300 E4/C5
FC-300 external expression pedal4/external
footswitch5
footswitch5
VB-99_e.book 153 ページ ２００８年８月１８日 月曜日 午後１時１０分