Fujitsu 2000 SERIES Manual Do Utilizador
CHAPTER 4 PCI Card Hot Maintenance in Red Hat Enterprise Linux 6
4.3 Hot replacement of IOU
4.3 Hot replacement of IOU
65
C122-E175-01EN
0000:82:00.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:83:09.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:84:00.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:02.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:08.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:09.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:10.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:11.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:89:00.0 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:89:00.1 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8c:00.0 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8c:00.1 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8f:00.0 Fibre Channel: Emulex Corporation Saturn-X:
LightPulse
Fibre Channel Host Adapter (rev 03)
0000:8f:00.1 Fibre Channel: Emulex Corporation Saturn-X:
LightPulse
Fibre Channel Host Adapter (rev 03)
(rev ca)
0000:83:09.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:84:00.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:02.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:08.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:09.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:10.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:85:11.0 PCI bridge: PLX Technology, Inc. Device 8748
(rev ca)
0000:89:00.0 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:89:00.1 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8c:00.0 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8c:00.1 Ethernet controller: Intel Corporation I350
Gigabit
Network Connection (rev 01)
0000:8f:00.0 Fibre Channel: Emulex Corporation Saturn-X:
LightPulse
Fibre Channel Host Adapter (rev 03)
0000:8f:00.1 Fibre Channel: Emulex Corporation Saturn-X:
LightPulse
Fibre Channel Host Adapter (rev 03)
NIC on the IOU (including onboard NIC)
For replacing IOU itself (replacement of onboard NIC) or expanding, replacing or removing NIC on the IOU,
not only common procedure of IOU replacement but also special procedure before and after powering on or
powering off IOU is needed. Here describes case of replacement of IOU itself. (otherwise add note) The
procedure describes operations where a single NIC is configured as one interface. It also describes cases
where multiple NICs are bonded together to configure one interface (bonding configuration). For bonding
multiple NIC by using PRIMECLUSTER Global Link Services (GLS), see 'PRIMECLUSTER Global Link
Service Configuration and Administration Guide Redundant Line Control Function' (J2UZ-7781).
For replacing IOU itself (replacement of onboard NIC) or expanding, replacing or removing NIC on the IOU,
not only common procedure of IOU replacement but also special procedure before and after powering on or
powering off IOU is needed. Here describes case of replacement of IOU itself. (otherwise add note) The
procedure describes operations where a single NIC is configured as one interface. It also describes cases
where multiple NICs are bonded together to configure one interface (bonding configuration). For bonding
multiple NIC by using PRIMECLUSTER Global Link Services (GLS), see 'PRIMECLUSTER Global Link
Service Configuration and Administration Guide Redundant Line Control Function' (J2UZ-7781).
Notes
-
To perform hot replacement in a system where a bonding device is installed, design the system so that it
specifies ONBOOT=YES in all interface configuration files (the /etc/sysconfig/network-scripts/ifcfg-
eth*files and the /etc/sysconfig/network-scripts/ifcfg-bond*files), regardless of whether the NIC to be
replaced is a configuration interface of the bonding device.
An IP address does not need to be assigned to unused interfaces. This procedure is for preventing the
device name of the replacement target NIC from being changed after hot replacement. If ONBOOT=NO
also exists, the procedure described here may not work properly.
specifies ONBOOT=YES in all interface configuration files (the /etc/sysconfig/network-scripts/ifcfg-
eth*files and the /etc/sysconfig/network-scripts/ifcfg-bond*files), regardless of whether the NIC to be
replaced is a configuration interface of the bonding device.
An IP address does not need to be assigned to unused interfaces. This procedure is for preventing the
device name of the replacement target NIC from being changed after hot replacement. If ONBOOT=NO
also exists, the procedure described here may not work properly.