Jackson R24 Manual Do Utilizador
9. Remove the old heater gasket and throw away.
10. Apply the new heater gasket.
11. Take the new heater and slide it through the hole in the wash
tank and line it up so the wash tank studs fit in the holes on the
heater flange.
tank and line it up so the wash tank studs fit in the holes on the
heater flange.
12. Place the mounting nuts and lockwashers on the studs and
secure them with the ratchet and 1/2” socket.
secure them with the ratchet and 1/2” socket.
13. Place the heater wires on the heater and tighten them down
using the 3/8” nutdriver.
using the 3/8” nutdriver.
14. Using the torgue wrench or a torque nutdriver (if available)
torge the nuts holding the wires, jumpers and bus bars to 16 in-lbs.
torge the nuts holding the wires, jumpers and bus bars to 16 in-lbs.
15. Ensuring that all non-essential personnel are clear of the area,
place the drain stopper back in the wash tank and restore power
and water to the unit. Turn the unit on and allow it to fill normally.
place the drain stopper back in the wash tank and restore power
and water to the unit. Turn the unit on and allow it to fill normally.
18. Verify that there are no leaks around the heater. If there are,
attempt to tighten it down (with power secured to the unit at the
service breaker to prevent injury) as the tank will change shape
slightly as it heats up.
attempt to tighten it down (with power secured to the unit at the
service breaker to prevent injury) as the tank will change shape
slightly as it heats up.
19. Use the amp meter to take readings off of the power lines to the
heater, verifying the amperage draw to the machine data plate.
heater, verifying the amperage draw to the machine data plate.
20. Wait until the heater contactor kicks out (meaning that the tub
has reached the appropriate temperature) and allow the machine
to operate approximately ten minutes to verify that there are no
leaks and that the heater is maintaining the tank temperature.
has reached the appropriate temperature) and allow the machine
to operate approximately ten minutes to verify that there are no
leaks and that the heater is maintaining the tank temperature.
21. Replace the heater cover.
23. Replace the front door.
AFTER MAINTENANCE ACTIONS
Service personnel may want to drain the machine and
allow it to cool down. Secure power to the unit at the service break-
er and then verify the torque of all fasteners covered in this instruc-
tion.
er and then verify the torque of all fasteners covered in this instruc-
tion.
SPECIAL NOTES
Work performed on Jackson dishmachines by unautho-
rized or unqualified personnel may void the warranty. Before begin-
ning this or any other maintenance evolution on a unit under war-
ranty, you should contact a certified Jackson technician or Jackson
Technical Service. You can find a list of qualified service agencies
in the back of you unit’s installation manual.
ning this or any other maintenance evolution on a unit under war-
ranty, you should contact a certified Jackson technician or Jackson
Technical Service. You can find a list of qualified service agencies
in the back of you unit’s installation manual.
SPECIAL PARTS
Heater Replacement Kit: 6401-003-12-23*
*The kit contains a heater, gasket, mounting hardware for
the heater and instructions.
CONTACT INFORMATION
Jackson MSC Inc. provides technical support for all of the
dishmachines detailed in this manual. We strongly recommend that
you refer to this manual before making a call to our technical sup-
port staff. Please have this manual with you when you call so that
our staff can refer you, if necessary, to the proper page. Technical
support is available from 8:00 a.m. to 5:00 p.m. (EST), Monday
through Friday. Technical support is not available on holidays.
Contact technical support toll free at 1-888-800-5672. Please
remember that technical support is available for service personnel
only.
you refer to this manual before making a call to our technical sup-
port staff. Please have this manual with you when you call so that
our staff can refer you, if necessary, to the proper page. Technical
support is available from 8:00 a.m. to 5:00 p.m. (EST), Monday
through Friday. Technical support is not available on holidays.
Contact technical support toll free at 1-888-800-5672. Please
remember that technical support is available for service personnel
only.
www.jacksonmsc.com
Heater Replacement Instructions
Revision A (09/23/2005)
4