Lenmar Enterprises BCR3312V Manual Do Utilizador

Página de 3
 
If the battery has End or Side contacts 
Open the hinged jaw on the charger to unlock the moveable 
contacts. Pull up on the charger contacts to raise them above the top 
deck of the charger and expose the side facing contacts. Set the 
battery to be charged on the deck of the charger and against the 
fence (marked “D”) with its contacts facing the charger’s contacts. 
For large batteries or in some circumstances, the “D” fence may 
need to be reversed or removed to make more room for the battery. 
The same is true for the smaller “C” fence. Adjust the charger 
contacts up, down, left or right to line up with the contacts on the 
battery properly. When you are satisfied with the contact locations, close and latch the hinged jaw to lock the charger contacts into place. Set the 
battery down on top of the charger and slide the battery forward against the charger contacts to make good connection with the battery. Place the 
magnetic temperature sensor on top of the battery being charged. 
Connecting to other batteries 
Many rechargeable hobby batteries used for R/C (remote 
control) toys can plug directly into the charger on the end 
of the charger next to the power input connector. This is a 
standard connector and will fit many makes and types of 
hobby battery packs. For all other battery types, the 
optional clip lead will be required Plug the connector end 
of the clip leads into the charger base at the end next to 
the power input connector.  Use the alligator clips onto the exposed contacts on the battery to be charged. Be careful not to crush or deform spring 
contacts made of bent sheet metal. Place the magnetic temperature sensor on top of the battery being charged. 
The charge status display 
Once the charger unit has beeped to verify the battery is making proper contact, the charge indicator on the side of the unit will show the progress 
of the charge.
 
Charge Status Display 
Indicators
 
(   = off, 
 = on )
 
Charge Level 
Yellow LED only (Flashing) 
 
0-33% 
Yellow + 1 Red LED 
 
33-66% 
Yellow + 2 Red LED’s 
 
66-99% 
Red LED only 
 
Full / Complete 
The charger will automatically stop the charge and beep when a full charge is detected on the battery. The charge indicator will show only 1 Red 
light to indicate the battery has reached full charge. The time required to reach a full charge will vary depending on the capacity of the battery and 
how much charge is already in it before you start.  
Reconditioning  (for Ni-Cd type batteries only) 
NiCd batteries are prone to developing a “memory” if not occasionally fully discharged before they are recharged. No other types of batteries are 
subject to developing memory, so battery types other than NiCd should not be reconditioned. Make sure the unit is connected to power, and 
connect the NiCd battery to be reconditioned/recharged. Once the charger beeps to indicate that the battery is properly connected, breifly press 
the Discharge button on the front of the unit.  The unit will beep 2 times and the green DISCHARGE light will go on. The DISCHARGE light will 
stay on until the battery is fully discharged, then the charger will switch automatically into the charge mode and charge the battery fully. 
Depending on the capacity of the battery and the amount of charge present, the discharge cycle could take many hours to complete. 
 
NOTE: You should only use the Discharge feature with a Ni-Cd type battery. Discharging  other type batteries may cause damage to the 
battery’s ability to accept a full charge in the future. 
Battery Compatibility 
This charger will charge virtually any NiMH, NiCd, or Lead Acid battery, but is ideally suited for use with the following Lenmar  batteries: 
CBE22, DMC50, MB72S, OBC84S, PV20, SBT30, SBT73, SG683 
Limited 3 Year Warranty 
This limited warranty starts from the date of original purchase and expires 3 years thereafter. 
If any part, because of manufacturing defects or workmanship fails to function properly under normal use will be repaired at no charge for parts and labor or, at our option, the 
product will be replaced.  The following is excluded: damages from delay or loss of use of equipment, or damaged batteries, malfunctions resulting from misuse, tampering, 
unauthorized repairs, modifications, or accident. 
Package the unit and its accessories carefully using ample padding material to prevent damage in transit and ship it prepaid and insured to: 
LENMAR ENTERPRISES INC. USA , 4035 Via Pescador, Camarillo, CA. 93012. 
When sending in product for service, your package should include evidence of date and place of purchase.  Enclose $10.00 for shipping and handling for addresses in the U.S.  For 
outside the U.S. and Canada, freight will vary depending upon ship to address. 
 
The following statement is required in the state of California pursuant to the settlement of an action brought by the Mateel Environmental Justice 
Foundation against multiple electronics and appliance manufacturers  
WARNING:  Handling the cord on this product will expose you to lead, a chemical known to the state of California to cause birth defects or other 
reproductive harm.  Wash hands after handling. 
 
 
 
BCR3312V    
 
 
 
 
 
 
 
                           202-171