Viking F20875 EN Manual Do Utilizador
26
27
P
ro
d
u
ct
C
a
re
P
ro
d
u
ct
C
a
re
NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with an appliance bulb of the same size, shape,
and wattage (no greater than 40 watts).
replace the bulb with an appliance bulb of the same size, shape,
and wattage (no greater than 40 watts).
• The dispenser lights and refrigerator compartment lights are LEDs
that cannot be changed.
To Replace the Appliance Bulb in the Freezer:
1. Unplug refrigerator or disconnect power.
2. Remove the light shield(s), if necessary.
1. Unplug refrigerator or disconnect power.
2. Remove the light shield(s), if necessary.
• Squeeze both sides of the light shield
while pulling downward to remove.
3. Replace burned-out bulb(s) with
appliance light bulb(s) no greater than
40 watts.
40 watts.
4. Replace the light shield(s) by inserting the tabs on the shield into
the liner holes and snap into place.
NOTE: To avoid damaging the light shield, DO NOT force the
shield beyond the locking point.
shield beyond the locking point.
5. Plug in refrigerator or reconnect power.
Clean the Touch Screen Display on the Dispenser Panel
1. Make sure the refrigerator is unplugged or the power is
disconnected before wiping the screen, to avoid unintentionally
changing the settings.
changing the settings.
2. Mix a solution of mild detergent in warm water. Dampen a soft, lint-
free cloth with the solution and gently wipe the screen.
NOTE: DO NOT spray or wipe liquids directly onto the screen,or
over-saturate the cloth.
over-saturate the cloth.
3. Plug in refrigerator or reconnect power.
Clean the Exterior Surfaces
1. Unplug refrigerator or disconnect power.
2. Using a clean sponge or soft cloth and a mild detergent in warm
2. Using a clean sponge or soft cloth and a mild detergent in warm
water, wash, rinse and thoroughly dry stainless steel and painted
metal exteriors.
metal exteriors.
• To keep your stainless steel refrigerator looking like new and to
remove minor scuffs or marks, it is suggested that you use stainless
steel cleaner and polish.
steel cleaner and polish.
IMPORTANT: This cleaner is for stainless steel parts only.
DO NOT allow the stainless steel cleaner and polish to come into
contact with any plastic parts such as the trim pieces, dispenser covers
or door gaskets. If unintentional contact does occur, clean plastic part
with a sponge and mild detergent in warm water. Dry thoroughly with
a soft cloth.
contact with any plastic parts such as the trim pieces, dispenser covers
or door gaskets. If unintentional contact does occur, clean plastic part
with a sponge and mild detergent in warm water. Dry thoroughly with
a soft cloth.
3. Plug in refrigerator or reconnect power.
Clean the Condenser
There is no need for routine condenser cleaning in normal home
operating environments. If the environment is particularly greasy or
dusty, or there is significant pet traffic in the home, the condenser
should be cleaned every 2 to 3 months to ensure maximum efficiency.
operating environments. If the environment is particularly greasy or
dusty, or there is significant pet traffic in the home, the condenser
should be cleaned every 2 to 3 months to ensure maximum efficiency.
To clean the condenser:
1. Unplug refrigerator or disconnect power.
2. Remove the base grille.
3. Use a vacuum cleaner with a soft brush to clean the grille, the open
1. Unplug refrigerator or disconnect power.
2. Remove the base grille.
3. Use a vacuum cleaner with a soft brush to clean the grille, the open
areas behind the grille and the front surface area of the condenser.
4. Replace the base grille when finished.
5. Plug in refrigerator or reconnect power.
5. Plug in refrigerator or reconnect power.
Cleaning
(cont.)
Changing the Light Bulb