Ariston G.C.N.:47-116-65 (24 kW) Manual Do Utilizador

40

Accessing the settings - adjustment - problem identifi cation 
menus
The boiler can be used to manage the heating and domestic hot 
water production system in its entirety.
Navigation within the menus enables the boiler system + 
connected peripheral units to be customised, optimising 
operation for maximum comfort and maximum saving. It also 
provides important information relating to the effi

  cient operation 

of the boiler.

Before access to the menus, the display show some “quick 
settings” to have direct access to the parameters.
To see all available parameters and menu access to view FULL 
MENU.

GAS - Direct access to the parameters:

SET - Direct access to the parameters:

PCB - Direct access to the parameters:

VIS - Direct access to the parameters:

ZONE - Direct access to the parameters:

FULL MENU  - see table on following pages

NETWORK
0

4

User Interface

Boiler Parameter
2

0

General setting

2

2

General setting

2

3

C.H. Parameters - Part 1

2

4

C.H. Parameters - Part 2

2

5

Domestic Hot Water

2

6

Boiler manual settings

2

7

Test & Utilities

2

8

Menù 2 Reset to factory setting

Zone 1 Parameters
4

0

Set-point Zone1

4

2

Zone 1 Setting

4

3

Diagnostics

Parametri Zona 2
5

0

Set-point Zone2

5

2

Zone 2 Setting

5

3

Diagnostics

Parametri Zona 3
6

0

Set-point Zone3

6

2

Zone 3 Setting

6

3

Diagnostics

Service Parameter
8

1

Statistics

8

2

Boiler

8

3

Boiler Temperature

8

4

Solar & Storage

8

5

Service

8

6

Error History

The parameters relating to each individual menu are listed in the 
following pages.
The various parameters can be accessed and modifi ed using the OK 
button and the encoder (see fi g. below). 
The description of the menus and of each individual parameter will be 
shown on the display.

6. E

SC

 button 

7. “encoder” 

8. O

K

 button  programming key

6

7

8

To access the Menus, proceed as follows (for example: “231

231”:

1.   Simultaneously  press  the

 ESC    button and OK button for 5 

seconds; the display show CODE and 222. 

 

Caution! The menus reserved for qualifi ed technicians may only 
be accessed after setting the access code.

2.  Turn the encoder 

 in a clockwise direction to select code 234

3.  Press the OK button; the display show the fi rst “quick setting” GAS

4.  Turn the encoder 

 to select  MENU;

5.   Press the OK button; the dispaly show the menu 

0

.

6.   Turn the encoder 

 in a clockwise direction to select the menu 

2

7.  Press the OK button to access to the menu. The display show the 

sub-menu 

20

8.

 

Turn the encoder 

 to select a sub menu 

23

; 

9.   Press the OK button to access the sub menu parameters; the 

display show 

230

10.  Turn the encoder 

 to select a parameter 

231

 

11. Press the OK button to access the parameter; the display will 

indicate the value, e.g “

70

”.

 

Note: The parameter value will be displayed for 20 seconds, then 
will begin to fl ash in alternation with the parameter, e.g. “

70

  > 

231

 “.

12.  Turn the encoder 

 to select the new value, e.g. “

75

”.

13.  Press OK button to save the change or press E

SC

 to exit without 

saving.

To exit, press the E

SC

 button until the normal display screen is restored.

For menus which do not require the access code, it is possible to pass 
directly from the menu to the sub menu.