Fujifilm s602 Manual Do Utilizador
17
Getting
R
eady
1
◆
Checking the Battery Level
◆
◆
Auto Power Off Function
◆
Number of Available Shots
Selecting the Language
The number of available shots is displayed on
the screen.
the screen.
２５０
２５０
Ｆ５．６
Ｆ５．６
００４９
００４９
Ｎ
●
!
See P.69 for information on changing the number of
recorded pixels/Quality (compression ratio) setting.
recorded pixels/Quality (compression ratio) setting.
●
!
The factory default settings set at shipment are
1
(Number of recorded pixels) and N (Quality: normal).
■
Standard Number of Shots for the Media
Because the amount of data needed to record an image varies slightly depending on the type of subject, the number of
available shots may not decrease after an image is recorded, or may decrease by 2 in some cases. Also, the difference
between the standard number of shots and the actual number of available shots increases for media with a higher capacity.
available shots may not decrease after an image is recorded, or may decrease by 2 in some cases. Also, the difference
between the standard number of shots and the actual number of available shots increases for media with a higher capacity.
✽
Number of available shots for formatted media.
Quality Mode
Image File Size
MG-4S (4MB)
MG-8S (8MB)
MG-16S/SW (16MB)
MG-32S/SW (32MB)
6
12
25
50
12
25
49
99
30
61
122
247
Approx.
2.4MB
Approx.
1.2MB
Approx.
620KB
Approx.
320KB
Approx.
130KB
FINE
NORMAL
MG-64S/SW (64MB)
MG-128SW (128MB)
26
53
13
6
3
1
Approx.
18MB
HIGH
3
7
1
0
0
0
56
113
28
13
6
3
101
204
198
398
497
997
Number of
recorded pixels
recorded pixels
3
2832
×
2128
4
640
×
480
FINE
NORMAL
NORMAL
8
17
33
68
2
6
12
25
6
13
26
53
Approx.
460KB
Approx.
1.3MB
Approx.
590KB
137
275
50
102
107
215
2
2048
×
1536
1
1280
×
960
BASIC
FINE
NORMAL
Microdrive 340MB
147
19
311
566
1119
2729
765
279
589
Microdrive 1GB
443
59
938
1642
3285
8213
2190
842
1729
If the camera is not used in any way for approx. 30 seconds when the camera functions are enabled, this
function temporarily switches features such as the LCD monitor off to reduce power consumption
(
function temporarily switches features such as the LCD monitor off to reduce power consumption
(
➡
P.73). If the camera is then left unused for a further period (2 or 5 minutes), the Auto Power Off function
automatically switches the camera off. To switch the camera back on, set the Power switch to “OFF”
briefly and then back to “
briefly and then back to “
U
” or “
Q
”.
Switch the camera on and check that no battery level icon (
X
or
C
) is displayed. If no icon is
displayed, the battery has sufficient remaining charge.
h
X
Lit red
: The batteries are low on charge. Replace the batteries as they will run out
shortly.
h
C
Blinking red: The batteries have no remaining charge. The display will shortly go blank and
the camera will stop working. Replace the batteries.
●
!
If the
C
icon starts flashing red while a movie is being shot, shooting automatically stops.
●
!
Do not reuse batteries that have no remaining charge (
C
blinking red) as this can result in faults such as the
camera switching off without retracting the lens.
ＳＥＴ−ＵＰ
ＳＥＴ−ＵＰ
ＵＳＢ ＭＯＤＥ
ＵＳＢ ＭＯＤＥ
ＤＡＴＥ／ＴＩＭＥ
ＤＡＴＥ／ＴＩＭＥ
ＲＥＳＥＴ ＡＬＬ
ＲＥＳＥＴ ＡＬＬ
ＲＥＳＥＴ ＡＬＬ
ＥＮＧＬＩＳＨ
ＥＮＧＬＩＳＨ
ＬＡＮＧＵＡＧＥ
ＬＡＮＧＵＡＧＥ
ＰＲＩＭＡＲＹ ＭＥＤＩＡ
ＰＲＩＭＡＲＹ ＭＥＤＩＡ
ＳＯＵＮＤ
ＳＯＵＮＤ
ＬＯＷ
ＬＯＷ
ＳＥＴ
ＳＥＴ
ＤＳＣ
ＤＳＣ
ＯＫ
ＯＫ
You can use the “SET–UP” screen on this
camera to select “ENGLISH”, “FRANCAIS” or
“DEUTSCH” as the “LANGUAGE” used for
screen display (
camera to select “ENGLISH”, “FRANCAIS” or
“DEUTSCH” as the “LANGUAGE” used for
screen display (
➡
P.68). The screens in this
manual are shown in “ENGLISH”.