Fujifilm S2-Pro Manual Do Proprietário

64

65

Check that the “p” (ready light) is displayed in
the viewfinder.

Bear in mind the composition, focus and effective flash range when taking pictures.

●

If the “

p

” (ready light) flashes for about 3 seconds after the shutter is released, this is a warning that the flash

fired at full power and the shot may be underexposed. Play the image back to check it. If you decide to retake
the shot, check the shooting distance, aperture, flash control range, etc. again before shooting.

●

If the subject is dark, the auxiliary AF-Assist illuminator fires to set the focus. See P.41 for details.

●

When you use the flash, shots are not taken continuously when the release mode is set to Continuous
Shooting.

●

If the built-in flash is charging, camera-shake correction is not performed on a VR lens while the shutter button
is pressed down halfway.

●

If you take a number of continuous shots with the built-in
flash, the “

p

” (ready light) may take a few moments to

light.

●

The shutter cannot be released unless “

p

” appears

without blinking in the viewfinder.

■ Effective Range of the Built-in Flash

Operation described in this section applies when the built-in flash and D- or G-type AF Nikkor
are attached.

Set the metering system selector dial to “Matrix
Metering” or “Center-weighted Metering”.

Set exposure mode and confirm shutter speed
and aperture.

The effective range of the built-in flash varies depending on the ISO sensitivity and aperture
settings used. Refer to the table below.

✽ Shutter speeds faster than the synchronized speed (1/125 sec.) cannot be set. When “125” appears in the

viewfinder display and the specified shutter speed flashes on the display panel, the actual shutter speed is
1/125 sec.

✽ The shooting distance is determined by the ISO setting and the aperture. For the “A” and “M” exposure modes,

see the table below.

✽ For the “P” exposure mode, the widest aperture that can be set by the camera varies depending on the ISO

setting. See P.69.

●

If you select “

l

” (Spot Metering), the flash control mode

is switched to “TTL”.

Synchronized shutter speed: 1/125
sec. See P.63 for details.

Automatically set by the
camera

Any aperture

3D Multi BL

TTL

1Press the flash pop-up button to pop up the

flash.

2Hold down the “a” button and,
3Turn the main command dial to select the

synchro mode.

●

When you are not using the flash, always keep it stowed
away to prevent battery depletion.

0

2

0

1

0

3

Widest aperture (built-in flash)

2.8

3.3

4

3.3

1.4

2.5-5.0

—

—

—

2

1.5-4.5

2.5-5.3

—

2.5-5.0

2.8

1.0-3.3

2.2-5.0

3.0-6.0

1.5-4.7

4

0.7-2.5

1.0-3.5

2.3-5.0

1.0-3.3

5.6

0.6-1.7

0.8-2.5

2.0-3.5

0.8-2.2

8

0.6-1.0

0.6-1.6

0.8-2.3

0.6-1.5

11

—

0.6-1.0

0.6-1.6

—

16

—

—

0.6-1.0

—

✽ The effective flash range can be calculated by dividing the guide number (12 for the built-in flash in this

camera) by the specified aperture.

●

When the sensitivity is set to ISO 800 or 1600, the built-in flash will fire but the correct exposure may not be
obtained. Use one of the following methods to check the results:
h Select “PREVIEW” as the photographed image display option in the SET–UP screen.
h Press the “

d

” button to play back the image.

Flash control range (m)