Fujifilm S2-Pro Manual Do Proprietário

103

102

1Quit all applications (FinePixViewer, etc.) that

are using the camera.

2Check that the Access lamp is off (that the

camera and computer are no longer
exchanging data).

Perform the steps shown below before you switch the camera off. This procedure differs
depending on the operating system software (or PC) you are using.

●

In some cases, the camera and computer may still be communicating even after the “Copying” message
disappears from the computer screen. Always check that the Access lamp is off.

For a USB connection, no action is needed on the computer.
If you are connecting via an IEEE1394 interface, use the disconnection procedure described
below.
1Left-click the Eject icon in the taskbar and eject “USB Disk”.
2The “Eject” menu option is displayed. Click this menu option.
3The “Eject hardware” dialog box appears. Click the [OK] button or the close button.

1Right-click the removable disk icon in the

“My Computer” window and select Eject.

3The  “Eject” menu option is displayed.

Click this menu option.

4The “Eject hardware” dialog box appears.

Click the [OK] button or the close button.

2Left-click the Eject icon in the taskbar

and eject “USB Disk”.

Drag the “Removable drive” icon on the desktop to the Trash.

●

When you drag the icon to the Trash, “REMOVE
OK” appears on the camera’s screen.

Switch the camera off and disconnect the IEEE1394 or USB cable.

✽ This step is only required in

Windows Me.

✽ Windows Me screen

1Load a media containing photographed

images into the camera.

2Switch the camera on.
3Select  “USB DOWNLOADING” as the “PC

MODE” setting in SET–UP (

➡P.89).

4Set the power switch to “OFF” to switch the

camera off.

●

Before connecting, you must install software on the
bundled CD-ROM on your computer.

●

Use of the AC power adapter (sold separately) is
recommended when connecting the camera to a
computer.

●

If a SmartMedia and Microdrive are both loaded into the
camera at the same time, the media selected in the
“MEDIA” setting in SET–UP is used (

➡“Setup”, P.89).

1Switch your PC on.
2Connect the special USB cable to the camera

and the computer.

3Switch the camera on.

●

In Windows XP and Mac OS X, automatic startup must be set up the first time you connect.

●

Take care to ensure that the cable is connected the right way round and that the plugs are firmly inserted all
the way into the sockets.

h When the camera and the computer are

exchanging data, the Access lamp blinks
orange.

h “USB DOWNLOADING” is displayed on the

rear display panel.

h The Auto Power Off function is disabled

while the camera is connected to a
computer.

●

When replacing the SmartMedia, always disconnect
the camera and computer first using the procedure
described on P.103.

●

Do not disconnect the USB cable during
communication. See P.103 for the disconnection
instructions.

0

1

0

2

h If FinePixViewer is installed, it starts up

automatically.

h A removable disk icon appears and you

can use your PC to transfer files to and
from the camera.

ＦＲＡＭＥ ＮＯ．

ＦＲＡＭＥ ＮＯ．

ＯＦＦ

ＯＦＦ

ＳＥＴ−ＵＰ

ＳＥＴ−ＵＰ

ＲＥＳＥＴ ＡＬＬ

ＲＥＳＥＴ ＡＬＬ

ＢＥＥＰ♪

ＢＥＥＰ♪

ＤＡＴＥ／ＴＩＭＥ

ＤＡＴＥ／ＴＩＭＥ

ＯＫ

ＯＫ

ＳＥＴ

ＳＥＴ

ＬＯＷ

ＬＯＷ

ＰＣ ＭＯＤＥ

ＰＣ ＭＯＤＥ

ＵＳＢ 

ＵＳＢ ＤＯＷＮＬＯＡＤＩＮＧ

ＤＯＷＮＬＯＡＤＩＮＧ

ＬＡＮＧＵＡＧＥ

ＬＡＮＧＵＡＧＥ

ＥＮＧＬＩＳＨ

ＥＮＧＬＩＳＨ

ＯＫ

ＯＫ

ＢＡＣＫ

ＢＡＣＫ

0

2

0

1

0

3

Always use the prescribed procedure when
disconnecting or switching off the camera
(

➡P.103).

If you are using a Windows PC, the driver settings are automatically specified when installation
ends. Simply wait a few moments.

✽ If your computer does not recognize the camera, refer to the Software Quick Start Guide.

If the above operations do not occur, you do
not have the required software programs or
drivers installed on your PC. Refer to the
Software Quick Start Guide booklet and
complete the required PC setup procedures.
Then reconnect the camera to your PC.

Windows

Macintosh