Fujifilm S2-Pro Manual Do Proprietário

117

116

(lit)

The AA-size batteries are flat.

Replace the AA-size batteries.

(blinking)

The built-in flash was popped up
even though the battery adapter is
used.

The built-in flash cannot be used if the
lithium batteries are not installed.

The AA-size batteries are low on
charge.

Have replacement AA-size batteries
ready.

1000 or more prints were specified in
the DPOF frame settings.

See P.92 for details.

The maximum number of frames for which
printing can be specified on the same
SmartMedia is 999. Set no more than 999
frames.

ＤＰＯＦ ＦＩＬＥ ＥＲＲＯＲ

i DPOF settings are already specified.
i The DPOF file contains an error or

was specified on another device.

To create a new DPOF file and reset all
the DPOF settings, press the “MENU/OK”
button.

ＲＥＳＥＴ ＤＰＯＦ ＯＫ

？

No media is inserted.

i Load a SmartMedia (3.3V) in the correct

direction.

i Load a Microdrive in the correct

direction.

i The media is not formatted

(initialized).

i The SmartMedia contact area

(gold-colored area) is soiled.

i The camera is faulty.

i Format the media.

i Wipe the SmartMedia contact area with

a soft, dry cloth. It may also be
necessary to format the SmartMedia. If
an error message still appears, replace
the SmartMedia.

i Contact your FUJIFILM dealer.

i The SmartMedia is not loaded

correctly.

i The SmartMedia contact area

(gold-colored area) is soiled.

i The media is damaged.
i The media format is incorrect.
i The camera is faulty.

i Push the SmartMedia all the way into

the slot and check that it is locked into
place.

i Wipe the SmartMedia contact area with

a soft, dry cloth. It may also be
necessary to format the SmartMedia. If
an error message still appears, replace
the SmartMedia.

i Contact your FUJIFILM dealer.

The media is full and no further data
can be recorded.

Erase some images or use a media that
has some available space.

The SmartMedia is write-protected.

Use a SmartMedia that is not write-
protected.

i You attempted to play back file that

was not recorded correctly.

i The SmartMedia contact area

(gold-colored area) is soiled.

i The camera is faulty.

i That data cannot be played back.

i Wipe the SmartMedia contact area with

a soft, dry cloth. It may also be
necessary to format the SmartMedia. If
an error message still appears, replace
the SmartMedia.

i Contact your FUJIFILM dealer.

Frame number 999-9999 has been
reached.

Use a formatted SmartMedia to take
pictures.

ＦＩＬＥ ＮＯ．ＦＵＬＬ

i Data cannot be recorded due to a

media fault or a problem with the
connection between the media and
the camera.

i The image you just shot is too large

to fit in the space available on the
media.

i Reload the media or switch the camera

off and then on again. If this does not
remedy the problem, contact your
FUJIFILM dealer.

i Use a new media.

You attempted to erase a protected
frame.

Protected frames cannot be erased.
Remove the protection using the camera
on which the protection was applied.

ＰＲＯＴＥＣＴＥＤ ＦＲＡＭＥ

You attempted to erase an image for
which DPOF settings have been
specified.

Erasing the image deletes the setting from
the DPOF specifications at the same time.

ＤＰＯＦ ＳＰＥＣＩＦＩＥＤ．

ＥＲＡＳＥ ＯＫ？

ＤＰＯＦ ＳＰＥＣＩＦＩＥＤ．

ＥＲＡＳＥ ＡＬＬ ＯＫ？

eThe table below lists the warning messages displayed on the

top display panel or in the viewfinder.

eThe table below lists the warnings that are displayed on the rear display panel.