Honeywell T7350 Manual Do Utilizador

Página de 40
T7350 COMMERCIAL PROGRAMMABLE THERMOSTAT
63-2605—5
18
OPERATION
Startup Operation
Upon initial thermostat powerup, a startup and initialization 
program begins. This startup occurs only on initial powerup. 
After total loss of power for an extended period, the current 
time and day can be lost (requiring reset). However, the 
thermostat retains the user program.
NOTE: With no program set, the thermostat controls to the 
Occupied default setpoints of 70°F (21°C) for heat 
and 75°F (24°C) for cool.
T7350 Relay Logic
All T7350 model thermostats contain four switching relays. In 
conventional applications, the relays control first stage cooling, 
first stage heating, fan, and auxiliary. In heat pump 
applications, the relays control the heat pump compressor, 
changeover, fan, and emergency heat.
NOTE: Models T7350B,D, T7350H1009 have subbases with 
more relays to accommodate extra stages.
Logic with Modulating Outputs (T7350H1017, M, only)
The specific relay logic depends on whether or not staging is 
employed. See Table 14.
NOTE: The modulating outputs always provide a signal.
Table 14. T7350 Modulating Relay Logic Exceptions.
a
See Table 15 for modulating output signal details.
To display the status of the modulating outputs:
1. Cycle through information displays using the info key.
2. The device displays a percentage value for each output:
a. MODHEAT on one screen.
b. MODCOOL on another screen.
Table 15. Modulating Output Signal.
O/B Terminal for Heat or Cool Changeover
The O/B terminal controls heat pump changeover. The default 
operation is for the terminal to be powered when calling for 
heat (or while the most recent call was for heat). This 
corresponds to a typical O terminal.
NOTE: The O/B terminal can be configured to operate as a 
typical B terminal (powered on call for cool).
Emergency Heat 
(select T7350 Thermostats only)
With the system set for Em Heat, auxiliary heat serves as 
stage one; compressor stages are locked off. The fan cycles 
with the auxiliary heat.
Equipment Protection
As part of the operational sequence, the T7350 
microprocessor incorporates cycle rate, and minimum on and 
off times for all heating and cooling stages. This extends 
equipment life as it prevents rapid cycling of equipment.
NOTE: Minimum on and off times are fixed.
Cycle Rates
The thermostat control algorithm maintains the temperature by 
cycling stages of heating or cooling to meet setpoint. Cycle 
rates, in cycles per hour (cph) are set using a PDA.
NOTE: Defaults are: heat: 6cph, cool: 3cph.
P+I+D Control
The T7350 microprocessor-based control requires that the 
user understands temperature control and thermostat 
performance. A conventional electromechanical or electronic 
thermostat does not control temperature precisely at setpoint. 
Typically, there is an offset (droop) in the control point as the 
system load changes. This is a phenomenon that most people 
in the industry know and accept.
IMPORTANT
• P+I+D (Loop Tuning) parameters are optimized for 
proper operation of a vast majority of HVAC systems. 
Only when completely certain of necessary and 
proper changes should you alter these values.
• Improper changes result in poor system performance 
and equipment problems such as compressor short 
cycling. Other problems include wide swings in space 
temperature and excessive overdriving of modulating 
outputs.
All adjustments to Loop Tuning parameters should be gradual. 
After each change, allow the system to stabilize to accurately 
observe the effects of the change. Then, as needed, make 
further refinements until the system operates as desired.
If adjustment of PID parameters is required, use the following:
NOTE: In the items that follow, the term “error” refers to the 
difference between the measured space temperature 
and the current actual space temperature setpoint:
— The Throttling Range (TR), also called Proportional Gain, 
determines the impact of the error on the output signal. 
Decreasing TR amplifies the error effect; that is, for a given 
error, smaller TR causes higher output signal.
— The Integral Time (IT), also called Integral Gain, 
determines the impact of the error-over-time on the output 
signal. Error-over-time has two components making up its 
value: amount of time the error exists; and size of the error. 
The higher the IT, the slower the control response. In other 
words, a decrease in IT causes a more rapid change to the 
output signal.
Modulating 
Output
a
Stages
Relay Action
Heat/ 
Cool
Fan
On 
(1 to 100 
percent)
0
On
Output reaches 10%: On
Output falls below 5%: Off
1 or 2
Staged 
Cycling
On/Off matches equipment 
stage operation
Off 
(0 percent)
0,1, or 2 Off
Off
Action
0 percent
100 percent
Direct
4 mA
20 mA
Reverse
20 mA
4 mA