Jacuzzi 5 corner style bath skirt Instrução De Instalação
Bath Skirt Installation
The bath should already be set and leveled. Electricity
should be connected and bath unit tested to be sure it is
working properly before installing the skirt.
should be connected and bath unit tested to be sure it is
working properly before installing the skirt.
Mount the five shell clips to the wooden blocks located
under the rim of the bath. (See Illustration 1.) Shell clips
are to be located 5/8" from the inside of the bath rim
edge. Mark hole locations on the blocks using one of the
clips as a template. Then drill pilot holes about 1/8" deep
with a 3/32" drill. Use caution to avoid drilling through
bath rim. Secure the clips to the wooden blocks as
shown.
under the rim of the bath. (See Illustration 1.) Shell clips
are to be located 5/8" from the inside of the bath rim
edge. Mark hole locations on the blocks using one of the
clips as a template. Then drill pilot holes about 1/8" deep
with a 3/32" drill. Use caution to avoid drilling through
bath rim. Secure the clips to the wooden blocks as
shown.
Place the 21" long aluminum angle strips at each side of
the bath. They should be located 7/8" from the stud wall
and 1/4" behind a plumb line dropped from the edge of
the bath rim. Fasten the aluminum angles to the sub-
floor using the screws provided (See Illustration 2.)
the bath. They should be located 7/8" from the stud wall
and 1/4" behind a plumb line dropped from the edge of
the bath rim. Fasten the aluminum angles to the sub-
floor using the screws provided (See Illustration 2.)
Clean an area about 2" long, approximately 4" from each
end, on the bottom of the skirt and on the skirt rail with
isopropyl alcohol. Attach strips of self-adhesive Velcro
end, on the bottom of the skirt and on the skirt rail with
isopropyl alcohol. Attach strips of self-adhesive Velcro
®
hook tape to the rail and the loop tape to the skirt, where
cleaned, ensuring that the tapes will mesh properly.
(See Illustration 3.)
cleaned, ensuring that the tapes will mesh properly.
(See Illustration 3.)
Lift skirt up under bath at a slight angle, engaging the
shell clips. Drop down and into place against skirt rail.
shell clips. Drop down and into place against skirt rail.
Follow the same procedure for the installation of the
other fixed skirt.
other fixed skirt.
To install the removable skirt. (See Illustration 4.) Lay
the remaining skirt rail (47-1/4" long) between the fixed
skirts. Ensure that the front edges of the side skirt panels
are in line with the contour of the bath rim edge and are
vertical. Locate the front surfaces of the skirt rail 5/8"
behind the front surfaces of the side panels as shown.
Fasten the bottom rail to the floor using the screws
provided.
the remaining skirt rail (47-1/4" long) between the fixed
skirts. Ensure that the front edges of the side skirt panels
are in line with the contour of the bath rim edge and are
vertical. Locate the front surfaces of the skirt rail 5/8"
behind the front surfaces of the side panels as shown.
Fasten the bottom rail to the floor using the screws
provided.
SCREWS
(PROVIDED)
(PROVIDED)
5/8"
SHELL CLIP
BATH
RIM
(Interior)
RIM
(Interior)
WOODEN
BLOCK
BLOCK
1.
7/8" FROM
STUD WALL
STUD WALL
1/4"
PLUMB LINE
OR SQUARE
FROM EDGE
OF BATH RIM
OR SQUARE
FROM EDGE
OF BATH RIM
2.
ALIGN CORNER OF SKIRT
WITH CORNER OF BATH RIM.
WITH CORNER OF BATH RIM.
VELCRO
HOOK TAPE
(Place on top side of
aluminum angle)
HOOK TAPE
(Place on top side of
aluminum angle)
VELCRO
LOOP TAPE
(Place on bottom
of skirt)
LOOP TAPE
(Place on bottom
of skirt)
3.
FIXED SIDE
PANEL
PANEL
5/8"
BOTTOM
RAIL
RAIL
BOTTOM
RAIL
RAIL
SCREWS
(PROVIDED)
(PROVIDED)
FIXED SIDE
PANEL
PANEL
4.