Black & Decker IR04VC_IB Manual

IMPORTANT SAFEGUARDS.

When using your iron, basic safety precautions should always be followed, 

including the following:

•  Only use iron for its intended use.

•   To avoid risk of electric shock, do not immerse the iron in water or other liquids.

•   Always turn iron off before plugging or unplugging from the electrical 

outlet. Never pull on the cord to disconnect the iron from the electrical 

outlet; instead, grasp the plug and pull on the plug to disconnect the iron.

•   Do not let the cord touch hot surfaces. Let the iron cool completely before 

putting the iron away. Coil the cord loosely around the iron when storing.

•   Always disconnect the iron from the electrical outlet before filling the iron 

with water, emptying the water from the iron, and when the iron is not in use.

•   Do not operate the iron with a damaged cord or in the event the iron has 

been dropped or damaged. To avoid the risk of electric shock, do not 

disassemble the iron. Take it to a qualified serviceman for examination and 

repair. Incorrect assembly might result in a risk of electric shock when the 

iron is used after reassembly.

•   Close supervision is necessary for any appliance used by or near children. 

Do not leave the iron unattended while the iron is connected or on an 

ironing board.

•   Burns can occur from touching hot metal parts, hot water or steam. Use 

caution when you turn a steam iron upside down— there might be hot 

water in the reservoir.

•   This appliance is not intended for use by persons (including children) with 

reduced physical, sensory or mental capabilities, or lack of experience 

and knowledge, unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible for their safety.

•  Children should be supervised to ensure that they do not play with the appliance.

•   The iron must be used and rested on a stable surface. 

•   When placing the iron on its stand, ensure that the surface on which the 

stand is placed is stable.

•   The iron is not to be used if it has been dropped, if there are visible signs of 

damage or if it is leaking.

SPECIAL INSTRUCTIONS. 

•  To avoid a circuit overload, do not operate an iron on the same circuit with 

another high wattage appliance.

•  If an extension cord is absolutely necessary, a cord with an ampere rating 

equal to or greater than the maximum rating of the iron should be used. A 

cord rated for less amperage can result in a risk of fire or electric shock 

due to overheating. Care shall be taken to arrange the cord so that it cannot 

be pulled or be tripped over.

SAVE THESE INSTRUCTIONS.

This appliance has a polarized plug (one blade is wider than the other). To 

reduce the risk of electric shock, this plug is intended to fit into a polarized 

outlet only one way. If the plug does not fit fully into the outlet, reverse the 

plug. If it still does not fit, contact a qualified electrician. Do not attempt to 

modify the plug in any way.

Warning: This appliance is equipped with a tamper-resistant screw to 

prevent removal of the outer cover. To reduce the risk of fire or electric shock, 

do not attempt to remove the outer cover. There are no user-serviceable parts 

inside. Repair should be done only by authorized service personnel.

Note: If the power supply cord is damaged, it should be replaced by qualified 

personnel; in Latin America, by an authorized service center.

This product is for household use only.

•  Remove any labels, stickers or tags attached to the body or soleplate of the iron.

•  Please go to www.prodprotect.com/applica to register your warranty.

Note: Use ordinary tap water for ironing. Do not use water processed through a 

home softening system.

Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or hem) 

before ironing.

1. Tilt the iron and using a clean measuring cup, pour water into opening until the  

    water reaches the MAX level mark on the water tank. Do not overfill.

2. Plug iron into electrical outlet.

Smart Steam

TM 

Technology

The Smart Steam

TM 

 system automatically generates the right amount of steam 

for the fabric type selected. Once you select the temperature, the Smart Steam

TM

 

technology detects the temperature and adjusts the steam power accordingly. 

1.  Turn fabric-select dial to appropriate setting (between 4 and 6) for your fabric. See   

     fabric guide on top of the water tank and read garment’s label   

    to help you determine fabric guide. Be sure there is water in the reservoir. Steam is  

    automatically turned off between settings 0 and 3.

2. When finished ironing, turn the fabric select dial to 0 and unplug the iron.

Important: Always stand the iron on its heel rest when powered on but not in use.

1.  Be sure the iron is filled with water.

2. On first use, pump the spray button several times.

1.  Turn the fabric -select dial to setting between settings 1, 2 or 3 (DRY) to iron 

without steam. The Smart Steam

TM

 system will automatically turn steam off. 

2. To dry iron at higher settings, empty the water from the tank to prevent steaming.

The anti-drip system prevents water spotting at low temperatures.

•   Once the iron reaches appropriate temperature, it will turn off after 30 

seconds of inactivity if left on its soleplate. If left vertically on its heel rest, it 

will shut off after 8 minutes.

•   As soon as you pick up the iron, it will start heating again. Wait for iron to 

reheat completely before resuming operation.

This product contains no user serviceable parts. Refer service to qualified service 

personnel.

1. Make sure iron is unplugged and has cooled completely. Wipe the    

   soleplate and outer surfaces with a soft cloth dampened with water and  

   mild household detergent. Never use abrasives, heavy-duty cleansers,   

   vinegar or scouring pads that may scratch or discolor the iron.

2. After cleaning, steam iron over an old cloth to remove any residue from  

    the steam vents.

1. Unplug the iron and let it cool completely.

2. Check that the fabric select dial is set to 0.

3. Store iron on its heel rest.

For service, repair or any questions regarding your appliance, call the 

appropriate 800 number on the cover of this book.

 Do not return the product 

to the place of purchase. Also, please 

Do not mail product back to the 

manufacturer, nor bring it to a service center. You may also want to consult 

the website listed on the cover of this manual.

• Any defect in material or workmanship provided; however, Applica’s liability 

   will not exceed the purchase price of the product.

• Two years from the date of original purchase with proof of such purchase.

• Provide you with a reasonably similar replacement product that is either 

   new or factory refurbished.

• Save your receipt as proof of date of sale.

• Check our on-line service site at www.prodprotect.com/applica, or call our 

   toll-free number, 1-800-231-9786, for general warranty service.

• If you need parts or accessories, please call 1-800-738-0245.

• Damage from commercial use

• Damage from misuse, abuse or neglect

• Products that have been modified in any way

• Products used or serviced outside the country of purchase

• Glass parts and other accessory items that are packed with the unit

• Shipping and handling costs associated with the replacement of the unit

• Consequential or incidental damages (Please note, however, that some 

   states do not allow the exclusion or limitation of consequential or incidental 

   damages, so this limitation may not apply to you.)

• This warranty gives you specific legal rights, and you may also have other  

   rights that vary from state to state or province to province.

8

9

7

5

6

1

2 3

4

EASY STEAM IRON

Product may vary slightly from what is illustrated.

1. Spray Nozzle

2. Water-fill opening

3. Fabric-select dial

4. Spray button

5. 360° pivoting cord

6. Heel rest

7. Fabric guide

8. Water tank

9. Soleplate

Model: IR04VC 
www.prodprotect.com/applica

© 2012 Applica Consumer Products, Inc.

is a registered trademark of The Black & Decker Corporation,  

Towson, Maryland, USA

Made and Printed in People’s Republic of China 

USA/Canada 1-800-231-9786

Accessories/Parts 1-800-738-0245

Register your product at www.prodprotect.com/applica

R1 2012/5-15-99E/F