PHL Audio 1660 Folheto

6.35 x 0

.8 F

AST O

N

 

Term

inal

4 x Ø 5.3 Holes on Ø 172

Ø 162.5 max.

Ø 139 max.

Ø 145.3 max.

68.5 max.

8

+

Red dot

Ø

 187.5 max.

(on angles)

Rated impedance 

Z

8

16

Ω

Reference efficiency (1 W@1 m)

-

97

97

dB SPL

Usable frequency range 

1

-

300–5000

300–5000

Hz

Power handling capacity 

2

(AES)

-

250

250

W

Max Sound Pressure Level  

3

SPLmax

117

117

dB SPL

Min. impedance modulus

Zmin

5.8 @ 650Hz

13.5 @ 600Hz

Ω

Voice-coil inductance 

4

@ 1 kHz

Le1k

0.55

1.51

mH

@ 10 kHz

Le10k

0.26

0.72

mH

Bl product

Bl

9.8

16.1

N/A

Moving mass

Mms

0.0110

0.0110

Kg

Resonance frequency 

5

Fs

125 (±25)

125 (±25)

Hz

DC resistance 

6

Re

5.4 (±0.5)

11.6 (±1.1)

Ω

Mechanical quality factor

Qms

4.1

4.1

1

Electrical quality factor

Qes

0.49

0.39

1

Total quality factor

Qts

0.43

0.35

1

Mechanical suspension compliance

Cms

145

145

10

-6

m/N

Effective piston area

Sd

0.0150

0.0150

m

2

Equivalent Cas air load

Vas

0.0045

0.0045

m

3

Max. linear excursion

Xmax

±2.0

±2.0

mm

Linear displacement volume

Vd

0.030

0.030

10

-3

m

3

Half-space efficiency

1.8

2.3

%

Unity load volume

Vas Qts

2

0.89

0.95

10

-3

m

3

Short term max. input voltage 

7

Vmax

90

130

V

Max. excursion before damage 

Xdam

4.0

4.0

mm

Ambient operating temperature 

–10    to   +50

°C

Storage temperature 

8

–20    to   +70

°C

Environmental conditions 

9

Outdoor

✚ 

Air volume occupied by the driver 

10

0.64

0.64

10

-3 

m

3

Speaker net mass

2.6

2.6

Kg

Recommended reflex box 

Vb/Fb

3 / sealedL  /  Hz

Electrical polarity

A positive voltage applied on the red 

terminal produces forward cone motion.

Note 1 : Allowing for energy response, excursion 

capability, Power spectrum, and -3dB low
freq. roll-off for standard reflex tuning.

Note 2 : Established at 20°C ambient temp, according to 

AES2-1984 standard using IEC268-1 simulated
programme signal and a 3 liter sealed test enclosure
with a 2nd order high-pass filter @ 400Hz.

Note 3 : Established at 1m on axis of the loudspeaker mounted

in test enclosure, when driven at full AES Power
Handling Capacity, including 4dB of thermal
compression loss.

Note 4 : Measured at 20 mA in free air.

Note 5 : Measured at 20 mA and 20°C ambient temp. 

in free air conditions, after full run and rest.

Note 6 : Measured at 20°C ambient temp. 

QC limits are ±10 %

Note 7 : Stated in RMS voltage according to IEC 268-5.

Note 8 : Includes shipping conditions. The lower limit prevents

from demagnetization.

Note 9: Our products are classified in three categories : 

Indoor, Outdoor, and Outdoor

✚  

for permanent

outdoor use or severe conditions. 

Note 10 : Calculated for front mounting on to a 18 mm thick

board.

PHL Audio S.A. provides these specifications as representative of current production after conditioning. Because of our continuous research, they are subject to change without notice.

461, rue des chênes 

■

Z.A

7 7 5 9 0   C H A R T R E T T E S

FRANCE

T é l : 33 01 64 81 29 80

Fax : 33 01 60 69 10 28

e-mail : phlaudio@phlaudio.com

http: //www.phlaudio.com

■