Budda V30H Manual Do Utilizador
4
1
2
3
6
9
4
5
7
8
10
11
12
13
14
The Front Panel:
1. Input: Connect your instrument here by
means of a shielded signal cable.
means of a shielded signal cable.
2. Clean Volume: Use this control to adjust
the output level of the Clean Channel.
the output level of the Clean Channel.
3. Clean/Overdrive: This switch, when de-
pressed, selects the Overdrive Channel.
When this switch is in the out position, the
Clean Channel is selected.
pressed, selects the Overdrive Channel.
When this switch is in the out position, the
Clean Channel is selected.
4. Overdrive Gain: Use this control to
adjust the gain of the Overdrive Channel.
With the control towards the counter clock-
wise position, the gain is low and very little
distortion is present. As you rotate the con-
trol clockwise the gain increases, produc-
ing more overdrive distortion and a higher
output volume level.
adjust the gain of the Overdrive Channel.
With the control towards the counter clock-
wise position, the gain is low and very little
distortion is present. As you rotate the con-
trol clockwise the gain increases, produc-
ing more overdrive distortion and a higher
output volume level.
5. Treble: Use this control to adjust the out-
put level of the high frequencies. This con-
trol provides 12dB of cut or boost at 6kHz.
put level of the high frequencies. This con-
trol provides 12dB of cut or boost at 6kHz.
6. Boost: This switch, when depressed,
increases the output by 10dB at 900Hz,
giving the middle frequencies more punch.
increases the output by 10dB at 900Hz,
giving the middle frequencies more punch.
7. Mid: Use this control to adjust the output
level of the middle frequencies. This control
provides 10dB of cut or boost at 1kHz.
level of the middle frequencies. This control
provides 10dB of cut or boost at 1kHz.
8. Bass: Use this control to adjust the out-
put level of the low frequencies. This con-
trol provides 8dB of cut or boost at 150Hz.
put level of the low frequencies. This con-
trol provides 8dB of cut or boost at 150Hz.
9. Presence:
This switch, when
depressed, increases the output level of
the high frequencies by 8dB at 10kHz, giv-
ing a more “glassy” sound to the amplifier.
This helps the output of the amplifier cut
through “acoustically dead” rooms.
the high frequencies by 8dB at 10kHz, giv-
ing a more “glassy” sound to the amplifier.
This helps the output of the amplifier cut
through “acoustically dead” rooms.
10. Overdrive Level: Use this control to
adjust the output level of the Overdrive
Channel.
adjust the output level of the Overdrive
Channel.
11. Reverb: Use this control to adjust the
amount of reverberation applied to the sig-
nal. With the control fully counter clockwise
no reverb is applied. As you rotate the con-
trol clockwise the amount of reverb increas-
es.
amount of reverberation applied to the sig-
nal. With the control fully counter clockwise
no reverb is applied. As you rotate the con-
trol clockwise the amount of reverb increas-
es.
12. Lamp: This lamp illuminates when the
amplifier is turned on.
amplifier is turned on.
13. On/Standby: Use this switch to acti-
vate the amplifier. The On/Off switch (#14)
should be turned on first. Allow 20 seconds
for the amplifier to warm up before turning
the Standby switch on.
vate the amplifier. The On/Off switch (#14)
should be turned on first. Allow 20 seconds
for the amplifier to warm up before turning
the Standby switch on.
14. On/Off: Use this switch to turn the
amplifier on and off. This switch should be
turned on at least 20 seconds before turn-
ing the Standby switch (#13) on.
amplifier on and off. This switch should be
turned on at least 20 seconds before turn-
ing the Standby switch (#13) on.
G u i t a r A m p l i f i e r H E A D