Navini Networks Ripwave 40-00097-00 Manual Do Utilizador
Ripwave Modem User Guide Navini Networks, Inc.
Part #40-00097-00 Rev E v1.0
July 30, 2003
32
ADDENDUM 1: Ripwave
™
Modem - PC Troubleshooting
- For Use With All Ripwave Modems & Navini Monitor Software -
PC Operating Systems
Prior to installing the Navini Monitor software, please check to insure that the PC Operating System
meets the criteria given in the table below. If these criteria are not met, unpredictable problems may
occur as a result of installation. It is recommended that the user have the latest Windows
meets the criteria given in the table below. If these criteria are not met, unpredictable problems may
occur as a result of installation. It is recommended that the user have the latest Windows
c
updates
installed prior to installing the Navini Monitor software.
Operating System
Ethernet interface
USB interface
Notes
Win95
Supported
Not Supported
1, 2
Win98
Supported Supported
2
Win98, 2nd ed.
Supported Supported
2
WinME
Supported Supported
2
Win 2000
Supported Supported
2,
4
Win NT 3.0/4.0
Supported
Not Supported
2, 4
Win XP
Supported Supported
3,
4
Note 1: USB was not supported in this software release
Note 2: Internet Explorer 3.0 or higher is required
Note 3: Requires Service Pack 1
Note 4: To load the Navini Monitor software, the user MUST have Administrative privileges.
Note 2: Internet Explorer 3.0 or higher is required
Note 3: Requires Service Pack 1
Note 4: To load the Navini Monitor software, the user MUST have Administrative privileges.
USB Interface
The USB Modem allows for a single PC to be connected to the Ripwave Modem via a USB interface, or
multiple PC’s connected via a USB hub. The Modem conforms to USB 1.1 standards. The Ethernet
packets generated by the PC are encapsulated within the USB protocol and transferred to the Modem.
The packets are then sent over-the-air. The USB Modem is fully supported for PC’s using Windows 98,
Windows ME, Windows 2000, and Windows NT 5.0.
To install the Modem using a USB interface, you must connect the Modem to the PC first and insert the
Navini Monitor CD to load the drivers. This will load the Miniport driver. After installing the USB
Miniport driver, the PC may or may not need to be restarted, depending upon the type of Operating
System and the particular installation. The system will prompt if a reboot is necessary.
Run the setup on the Navini Monitor CD. This will now load the Navini Monitor software.You must
ALWAYS reboot the PC after installing the Navini Monitor software. Also, you must ALWAYS reboot
after UNinstalling the Navini Monitor software. Failure to do so under either circumstance may gravely
affect PC operation.
multiple PC’s connected via a USB hub. The Modem conforms to USB 1.1 standards. The Ethernet
packets generated by the PC are encapsulated within the USB protocol and transferred to the Modem.
The packets are then sent over-the-air. The USB Modem is fully supported for PC’s using Windows 98,
Windows ME, Windows 2000, and Windows NT 5.0.
To install the Modem using a USB interface, you must connect the Modem to the PC first and insert the
Navini Monitor CD to load the drivers. This will load the Miniport driver. After installing the USB
Miniport driver, the PC may or may not need to be restarted, depending upon the type of Operating
System and the particular installation. The system will prompt if a reboot is necessary.
Run the setup on the Navini Monitor CD. This will now load the Navini Monitor software.You must
ALWAYS reboot the PC after installing the Navini Monitor software. Also, you must ALWAYS reboot
after UNinstalling the Navini Monitor software. Failure to do so under either circumstance may gravely
affect PC operation.