Manual Do Utilizadoríndice analíticoOPERATOR’S MANUAL1RHINO®1To the Owner/Operator/Dealer2DEALER to CUSTOMER Pre-Delivery / Operation Instructions5ROTARY MOWER1TABLE OF CONTENTS7KEY OPERATION POINTS90Operating Noise Level/Sound Pressure90Warranty information90RHINO LIMITED WARRANTY911. LIMITED WARRANTIES911.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the ...911.02. Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship.911.03. This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, ...911.04. Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any nature on behalf of Manufacturer.912. REMEDIES AND PROCEDURES.912.01. This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer within 30 days of purchase.912.02. Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the claim is based912.03. Purchaser is responsible for returning the goods in question to the Dealer.912.04. If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, Manufacturer will:912.05. Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for...913. LIMITATION OF LIABILITY.913.01. MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.913.02. MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR USE OF THE GOODS.913.03. EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLU...913.04. NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS OCCURRED.914. MISCELLANEOUS.914.01. Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County, Texas.914.02. Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term.914.03. If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein.914.04. Applicable law may provide rights and benefits to purchaser in addition to those provided herein.91INTRODUCTION SECTION87DEALER SETUP INSTRUCTIONS94SHIELD ASSEMBLY94SHEAR BOLT DRIVELINE INSTALLATION95A-FRAME INSTALLATION (Standard Hitch)951. Attach “A” Frames (1) to inside of welded hitch brackets on Mainframe, insert Hitch Pin (12), lockwasher (14) and install nut (13).952. Install the lift straps (3) on outside of top rails on main shield (behind geabox mount) and attach with 1/2” x 1-1/2” bolts (10) and locknuts (9).953. Insert spacer (7) into toggle (11) between “A” Frames (1). Insert 3/4” x 6” bolts (8) through hole in lift straps and spacer (7). Secure with 3/ 4” locknut (9).954. Assemble driveline support flat (15) and retain using 1/2’ x 1-1/2” bolt (10) and locknut (9).95TAIL WHEEL INSTALLATION (Standard or Quick Hitch)961. Align Tailwheel Beam Weldment (5) between pivot brackets located behind gearbox mount on Mainframe Weldment. NOTE: Long side of caster fork pivot tube is positioned up. Attach the Tailwheel Beam Weldment (5) to the Mainframe Weldment with one 5/8...962. Insert the Caster Fork Weldment (2) into Tailwheel Beam Weldment (5) and retain with Flatwasher (6) and Cotter Pin (7).963. Tighten all bolts to the proper torque. Figure Asm-R-024896HYDRAULIC RELIEF ASSEMBLY96For additional safety in transport, raise mower as high as possible without having driveline hit decks and shorten check chains all possible to prevent inadvertent falling in transport.97A-FRAME INSTALLATION (Quick Hitch)971. Attach the A-Frame Bars (1) to the right and left Hitch Lugs (8 & 9) with two Hitch Pins (2), washers (4), bushing (4), bushings (32), and Hex nuts (3).972. Attach the Lift Strap Bars (5) to the Mainframe with two 1/2”-13 x 1-3/4” bolts (14), 1/2” flatwasher (15), bushing (27) and 1/2”-13NC locknut (6).973. Attach flex links (7) to A-Frame bars (16) with 3/4” x 5” Hex bolts (12), bushings (30), flatwashers (29), Bushing (31), and Nut (13).974. Insert 1/2” x 2 bolt (10) through flex links (7), rear braces (5) and bushing (28) inserted in rear braces.975. Insert 1/2” x 2 bolt (10) through rear holes in flex link (7) with bushing (28) between and above rear braces. Figure Asm-R-031797Front and Rear Deflectors (Standard Equipment)98OFFSET ADAPTER HITCH (EXTRA EQUIPMENT)99ASSEMBLY SECTION93OPERATION SECTION101RHINO 148 ROTARY MOWER102OPERATION INSTRUCTIONS1021. OPERATOR REQUIREMENTS1032. TRACTOR REQUIREMENTS104Tractor Requirements and Capabilities1042.1 ROPS and Seat Belt1042.2 Tractor Safety Devices1042.4 3-Point Hitch1052.5 Front End Weight1052.6 Power Take Off (PTO)1062.7 Tire Spacing1063. GETTING ON AND OFF THE TRACTOR1073.1 Boarding the Tractor1073.2 Dismounting the Tractor1074. STARTING THE TRACTOR1085. CONNECTING THE MOWER TO THE TRACTOR1091. Make sure the tractor is equipped with the correct PTO shaft. Change shafts if needed.1092. Shorten or remove the tractor drawbar to avoid interference when raising and lowering the mower.1093. Board the tractor and start the engine. Position the tractor to the mower with the 3-point lift arms positioned between the respective set of mower A-frame lift lugs.1094. Turn off the tractor engine and dismount.1095. One lift arm at a time, align arm end hole between the set of A-frame lift lugs. Insert hitch pin through the lug and arm holes and insert retaining pin into hitch pin.1096. Walk around to opposite side and repeat procedure for remaining lift arm and hitch pin.1097. Extend or retract 3-point top link to align its end hole with the holes of the mower’s top link. Insert the top link hitch pin and insert retaining pin into hitch pin.1098. Adjust any lower link check chains, guide blocks, or sway blocks to prevent the mower from swaying side to side and possible contact with tractor rear tires.1095.2 Connecting Mower - Lift Type (Quick Hitch)1101. Make certain the implement’s upper and lower hitch pins are secured.1102. Lower the tractor’s 3-point lift until the three Quick-Hitch hooks are lower than the implements hitch pins. Carefully back the tractor to align the Quick-Hitch hooks under the implement’s hitch pins.1103. Slowly raise the tractor’s 3-point lift until the lower Quick-hitch hooks lock into place over the implement’s 3-point hitch pins.1101. Driveline length1112. Tractor stability1115.3 Safety Tow Chain1116. SETTING THE MOWER1116.1 Setting Mower Height- Lift Type - (Standard or Quick Hitch)1121. Park the tractor and mower on level ground.1122. Using the 3-point hitch control lever, position the front of the mower with the side skids 1” less off the ground than desired cut height. For example, for a 3” cut, position the skids 2” from the ground. Set the 3-point control lever stop a...1123. Shut down the tractor and remove the key.1124. Adjust the mower deck front to rear by extending or retracting the 3-point top link. Always set front of deck 3/4” lower than rear for best performance.1125. Level the mower side to side by manipulating one lower lift arm length. On most tractors, at least one of the lift arms is designed to allow for manipulation of its length. Shortening or extending will allow for deck leveling from side to side.1126. Securely block up the mower at this height.1127. Remove the bolts securing the tailwheel beam positioning bracket to the support brackets and allow the tailwheel to rest at ground level. Align beam and positioning brackets holes with closest set of holes in support brackets and reinstall bolts s...1128. Extend the tractor’s top 3-point link so that when lifting the mower, the front of the deck will raise 2 to 2½" before the tail wheel leaves the ground. This will allow the mower to follow the contour of uneven terrain.1126.2 Setting Deck Pitch1137. DRIVELINE ATTACHMENT1147.1 Driveline Length Check1148. PRE-OPERATION INSPECTION AND SERVICE1168.1 Tractor Pre-Operation Inspection/Service1178.2 Mower Pre-Operation Inspection/Service1178.3 Cutting Component Inspection1208.4 Blade Bolt Inspection1229. DRIVING THE TRACTOR AND IMPLEMENT1259.1 Starting the Tractor1269.2 Brake and Differential Lock Setting1269.3 Raising the Mower1279.4 Driving the Tractor and Mower12710. OPERATING THE TRACTOR AND IMPLEMENT12910.1 Foreign Debris Hazards13010.2 Bystanders/Passersby Precautions13010.3 Engaging the Power Take Off (PTO)13110.4 PTO RPM and Ground Speed13210.5 Operating the Mower1321. MAINTAIN MOWER SHIELDING in good operational condition,1362. DAILY INSPECT the condition of the Thrown Object Guards, mower Side Skirts, and skid shoes: Replace or repair worn or damaged guards.1363. DAILY INSPECT the condition of the Blades and Blade Bolts. Replace any cracked, worn, bent or damage blades. Always replace blade bolts and nuts when replacing blades. Make sure the blade bolts are properly tightened.1364. RAISE CUTTING HEIGHT to 6 INCHES minimum.1365. INSPECT AREA thoroughly before mowing to REMOVE potential THROWN OBJECT HAZARDS.1366. NEVER ALLOW BLADES to CONTACT SOLID OBJECTS like wire, rocks, posts, curbs, guardrails, or ground while mowing.1361. MARK objects that cannot be removed.1362. AVOID these objects when mowing.13610.7 Shutting Down the Implement13711. DISCONNECTING THE MOWER FROM THE TRACTOR13712. MOWER STORAGE13913. TRANSPORTING THE TRACTOR AND IMPLEMENT13913.1 Tire and Wheels14013.2 Transporting on Public Roadways14113.3 Hauling the Tractor and Implement14214. TROUBLESHOOTING GUIDE143Problem Possible Cause Remedy143Blades worn, dull, or bent. Replace blades.143(Refer to “Maintenance” section).143Mower not level side to side. Adjust. (Refer to “Assembly” section)143Improper height adjustment. Adjust Mower height.143(Refer to “Assembly” section)143Low tractor tire pressure on Adjust tire pressure.143one side. (Refer to your tractor operator's143manual)143Turning too fast. Reduce ground speed when turning.143Tractor tires push grass down. Adjust your tractor wheel spacing.143(Refer to “Operation” section)143Damaged Mower pan. Repair or replace as necessary.143RPM too low Use full PTO speed.143(Refer to your tractor operator's manual)143Improper blade for direction of cut. Install blades so rotation is correct.143rear to hold and circulate material longer. (Refer to Operation Section- Setting the Mower-Setting Deck Height) Reduce ground speed.143Cutting too high. Lower cutting height. (Refer to Operation Section-Setting the Mower- Setting Deck Pitch)143Windrowing Material heavy and lush. Raise the front of Mower relative to the or Uneven rear. (Refer to Operation Section-143Distribution Setting the Mower-Setting Deck143Height)143Excessive ground speed Reduce ground speed.143Conditions too wet. Wait for conditions to dry. Reduce143ground speed.143Bolt hole elongated or oversized. Replace Blade Carrier.143Locknut worn out. Replace Locknut.143Gearbox Noisy Low Lubricant. Check lubricant level.144Rough gears. Run in or change Gears.144Worn Bearing. Replace Bearing.144Bent Shaft. Replace Oil Seal and Shaft.144Oil Seal Race rough. Replace Shaft or repair Race.144Oil Seal installed wrong. Replace Seal.144Oil Seal not sealing in the housing. Replace Seal or use a sealant on O.D.144of Seal.144Oil level too high. Drain oil to proper level.144Gasket damaged. Replace Gasket.144Bolts loose. Tighten Bolts.144Sand hole in casting. Replace castings or gearbox.144Blades unable to cut that part of ground speed of tractor but keep144grass pressed down by path of engine running at full PTO wpm.144tractor tires. Lowering the cutting height may help.144Dull blades. Sharpen or replace blades.144Height of cutter lower at rear or See Cutting Height Instructions.144front.144Improper type lubricant. Replace with proper lubricant.144Excessive trash build-up around Remove trash.144gearbox.144Bearing or gears set up improperly. Consult your Dealer.144Excessively 540 RPM.144Heavy Material. Reduce ground speed. Raise cutting144height.144Not using proper pin. Replace only with recommended shear144pin.144PTO engaged at high engine RPM Idle engine to engage PTO144Cutting in rocky conditions Increase cutting height.144Blade carrier RPM too high. Check gearbox ratios.144Blades not properly heat treated. Consult your Dealer.144MAINTENANCE SECTION145HAZARDS WITH MAINTENANCE OF IMPLEMENT146PARTS INFORMATION147Lubrication147DRIVELINE LUBRICATION149SHEAR PIN YOKE LUBRICATION150BLADE SERVICING151BLADE SHARPENING152BLADE CARRIER REMOVAL152BLADE CARRIER INSPECTION153BLADE CARRIER INSTALLATION154BLADE REMOVAL154Blade Bolt Inspection155SEASONAL CLUTCH MAINTENANCE1571. Loosen nuts (Figure Mnt-R-0090) on springs until the springs are free, yet remain secure on bolts.1572. Attach cutter to tractor and start the tractor. Set the engine speed at 1200 RPM.1573. Mark outer plates as shown in Figure Mnt-R-0090.1574. Engage the PTO (approximately one second) and then quickly disengage it. The friction lining plates should break loose (check the mark).1575. Turn tractor off. Tighten the nuts on the disc spring clutch until Belleville spring is flat, then loosen each nut 2 turns.157STORAGE1571. Thoroughly clean the cutter.1572. Lubricate the cutter as covered in Maintenance Section.1573. Tighten all bolts and pins to the recommended torque.1574. Check the cutter for worn or damaged parts. Make replacements immediately.1575. Place driveline in storage position resting on bracket.1576. Store the cutter in a clean, dry place with the cutter housing resting on blocks.1577. Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the cutter.157PROPER TORQUE FOR FASTENERS157GENERAL SAFETY INSTRUCTIONS AND PRACTICES10OPERATOR SAFETY11CONNECTION OR DISCONNECTING IMPLEMENT SAFETY12CRUSHING HAZARDS13THROWN OBJECT HAZARDS141. MARK objects that cannot removed.142. AVOID these objects when mowing.141. BLADES CAN FAIL from impact and objects can be thrown with great velocity.152. INSPECT and REPLACE any damaged blades.153. CHECK blade carrier balance and REPLACE if damaged.15RUN OVER HAZARDS16PTO ENTANGLEMENT HAZARDS17MOWER BLADE CONTACT HAZARDS18HIGH PRESSURE OILLEAK HAZARDS19ELECTRICAL & FIRE HAZARDS20TRANSPORTING HAZARDS21HAZARDS WITH MAINTENANCE OF IMPLEMENT22PARTS INFORMATION23Decal Location244. D389 1 DANGER Multi-Hazard255. D388 1 DANGER Driveline Hazard256. D137 1 WARNING CCW Blade Rotation257. 00776678 1 DANGER Shear Bolt Length258. 00760657 1 IMPORTANT Genuine Parts259. D302 2 LOGO Rhino (4 x 6)2510. 00771283 1 WARRANTY 5 Year2511. D303 2 LOGO Rhino (4 x 16)2512. 00781322 2 NAME 1482513. 2738332 2 REFLECT Red Reflectors2514. NFS 1 SER PLT Serial Number Plate2515. 00756004 1** DANGER Shield Missing (Not Shown)2516. 00756005 1** DANGER Rotating Driveline (Not Shown)2517. 03200347 * REFLECT SMV2518. 00776031 1 ________ Canister, Operator’s Manual Inside2519. 00781398C 1 ________ Operator’s Manual2520. 10058000 3 ________ Bolt2521. 00024100 3 ________ Flatwasher2522. 02959924 3 ________ Locknut2523. D454 1 WARNING Crushing Hazard (Decal Under Deck)2524. D614 2 WARNING Thrown Object Shield Missing2525. D395 1 WARNING Blade Bolt Torque2526. D590 1 INSTRUCT Lubrication Chart25Decal Description26Federal Laws and Regulations33SAFETY SECTION9Tamanho: 10 MBPáginas: 178Languages: English, EspañolAbrir o manual