Manual Do Utilizadoríndice analíticoIntroduction8Projector Features8Package Contents9Projector with Lens Cap9AC Power Cord9VGA Cable (D-SUB to D-SUB)9Quick Start Guide9VGA - Component Adapter9Projector Overview10Using the Product12Control Panel12Connection Ports13Remote Control14Installing the Batteries151. Open the battery cover in the direction shown.152. Install batteries as indicated by the diagram Inside the compartment.153. Close the battery cover into position.15Remote Control Operation16Installation17Connecting the Projector17Powering On/Off the Projector18Powering On the Projector:181. Remove the projector lens cap.182. Complete the AC power cord and peripheral signal cable(s) connections.183. Press button to turn on the projector. The projector takes a minute or so to warm up.184. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.18Powering Off the Projector:181. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.182. Press button again to confirm.183. Disconnect the AC power cord from the electrical outlet and the projector.184. Do not turn on the projector immediately following a power off procedure.18Adjusting the Projector19Adjusting the Projector Height191. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.192. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.19Adjusting the Projector Zoom and Focus191. Focus the image by rotating the focus ring. A still image is recommended for focusing.192. Adjust the image by sliding the zoom ring.19Adjusting Projection Image Size20Menu Operation211. Press the Menu button on the control panel or the MENU button on the remote control to open the OSD menu.222. When OSD is displayed, use p / q to select any feature in the main menu.223. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.224. Adjust the settings with t / u.225. Press the Menu buttonon the control panel or the MENU button on the remote control, the screen will return to the main menu.226. To exit OSD, press the Menu button on the control panel or the MENU button on the remote control again. The OSD menu will close and the projector will automatically save the new settings.22Maintenance37Cleaning the Lens37Cleaning the Projector Housing37Replacing the Lamp381. Turn off the projector.392. If the projector is installed in a ceiling mount, remove it from the mount.393. Unplug the power cord.394. Loosen the screw in the side of the lamp cover and remove the cover.395. Remove the screws from the lamp module, raise the handle, and lift out the module.396. Insert the new lamp module into the projector and tighten the screws.397. Replace the lamp cover and tighten the screw.398. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.399. Reset the lamp hour. Refer to the “Setting” menu.39Specifications40Appendix41LED Indicator Messages41Compatibility Modes47Computer:47Video:47Troubleshooting48Start-up problems48Image problems48Tamanho: 4 MBPáginas: 54Language: EnglishAbrir o manual
Guia Do Utilizadoríndice analíticoIntroduction8Projector Features8Package Contents9Projector with Lens Cap9AC Power Cord9VGA Cable (D-SUB to D-SUB)9Quick Start Guide9VGA - Component Adapter9Projector Overview10Using the Product12Control Panel12Connection Ports13Remote Control14Installing the Batteries151. Open the battery cover in the direction shown.152. Install batteries as indicated by the diagram Inside the compartment.153. Close the battery cover into position.15Remote Control Operation16Installation17Connecting the Projector17Powering On/Off the Projector18Powering On the Projector:181. Remove the projector lens cap.182. Complete the AC power cord and peripheral signal cable(s) connections.183. Press button to turn on the projector. The projector takes a minute or so to warm up.184. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.18Powering Off the Projector:181. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.182. Press button again to confirm.183. Disconnect the AC power cord from the electrical outlet and the projector.184. Do not turn on the projector immediately following a power off procedure.18Adjusting the Projector19Adjusting the Projector Height191. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.192. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.19Adjusting the Projector Zoom and Focus191. Focus the image by rotating the focus ring. A still image is recommended for focusing.192. Adjust the image by sliding the zoom ring.19Adjusting Projection Image Size20Menu Operation211. Press the Menu button on the control panel or the MENU button on the remote control to open the OSD menu.232. When OSD is displayed, use p / q to select any feature in the main menu.233. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.234. Adjust the settings with t / u.235. Press the Menu buttonon the control panel or the MENU button on the remote control, the screen will return to the main menu.236. To exit OSD, press the Menu button on the control panel or the MENU button on the remote control again. The OSD menu will close and the projector will automatically save the new settings.23Maintenance38Cleaning the Lens38Cleaning the Projector Housing38Replacing the Lamp391. Turn off the projector.402. If the projector is installed in a ceiling mount, remove it from the mount.403. Unplug the power cord.404. Loosen the screw in the side of the lamp cover and remove the cover.405. Remove the screws from the lamp module, raise the handle, and lift out the module.406. Insert the new lamp module into the projector and tighten the screws.407. Replace the lamp cover and tighten the screw.408. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.409. Reset the lamp hour. Refer to the “Setting” menu.40Specifications41Appendix42LED Indicator Messages42Compatibility Modes48Computer:48Video:48Troubleshooting49Start-up problems49Image problems49Tamanho: 2 MBPáginas: 55Language: EnglishAbrir o manual
