Manuais de utilizador para Viewsonic PJD6221

índice analítico

• Notes on the AC Power Cord

  6
  • Introduction

    8
    • Projector Features

      8
    • Package Contents

      9
  • Projector with Lens Cap

    9
  • AC Power Cord

    9
  • VGA Cable (D-SUB to D-SUB)

    9
    • Projector Overview

      10
  • Using the Product

    12
    • Control Panel

      12
    • Connection Ports

      13
    • Remote Control

      14
    • Replacing the Battery

      15
      • 1. Push the catch to the left and remove the battery holder.

        15
      • 2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.

        15
      • 3. Push the battery holder back into the remote control until you feel a click.

        15
    • Remote Control Operation

      16
  • Installation

    17
    • Connecting the Projector

      17
    • Powering On/Off the Projector

      18
• Powering On the Projector:

  18
  • 1. Remove the projector lens cap.

    18
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    18
  • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.

    18
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    18
• Powering Off the Projector:

  18
  • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    18
  • 2. Press button again to confirm.

    18
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    18
  • 4. Do not turn on the projector right after power off.

    18
  • Adjusting the Projector

    19
• Adjusting the Projector Height

  19
  • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

    19
  • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.

    19
• Adjusting the Projector Zoom and Focus

  19
  • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

    19
  • 2. Adjust the image by sliding the zoom ring.

    19
• Adjusting Projection Image Size

  20
  • Menu Operation

    21
    • 1. Press the MENU button to open the OSD menu.

      23
    • 2. When OSD is displayed, use p / q to select any feature in the main menu.

      23
    • 3. After selecting the desired main menu item, press u to enter sub-menu for feature setting.

      23
    • 4. Use p / q to select the desired item and adjust the settings with t / u.

      23
    • 5. Press the MENU button, the screen will return to the main menu.

      23
    • 6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.

      23
  • Network Control

    28
    • 1. Connect one end of the internet cable to the Network Control connector on the projector.

      28
    • 2. Connect the other end of the internet cable to an available RJ-45 connector on your computer.

      28
    • 3. Turn on your projector and computer.

      28
    • 1. Enable DHCP from the projector OSD, under Network Config.

      28
    • 2. Start browser in PC and specify following URL, then click “Go” button.

      29
    • 3. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.

      29
    • 1. Set IP Address and Subnet Mask under Network Config.

      30
    • 2. From your computer, go to Start > Settings > Network and Dial-up Connections > Local Area Connection and right click to select Properties..

      30
    • 3. Select "Intel Protocol (TCP/IP)" and click "Properties".

      31
    • 4. Set your PC’s IP address, and click OK.

      31
    • 5. Start browser in PC and specify following URL, then click “Go” button.

      32
    • 6. If connection succeeds, the login screen is displayed. Enter your User name and Password and click “OK”. Below are the factory default settings for administrator, user and passwords.

      32
    • 1. Go to Tools > General and click "Settings".

      41
    • 2. Click "Every visit to the page" and "OK".

      42
    • 3. Click "OK" to exit "Internet Properties".

      42
  • Maintenance

    43
    • Cleaning the Lens

      43
    • Cleaning the Projector Housing

      43
    • Cleaning the Filter Cover

      43
      • 1. Switch the projector off and unplug the AC power cord from the wall socket.

        43
      • 2. Remove the filter cover as the illustration shown.

        43
      • 3. Clean the filter cover.

        43
      • 4. Replace the filter cover.

        43
      • 5. Attach the filter cover.

        43
      • 6. Plug the power back into the projector.

        43
    • Replacing the Lamp

      44
      • 1. Turn off the projector.

        45
      • 2. If the projector is installed in a ceiling mount, remove it

        45
      • 3. Unplug the power cord.

        45
      • 4. Loosen the screw in the side of the lamp cover and remove the cover.

        45
      • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.

        45
      • 6. Insert the new lamp module into the projector and tighten the screws.

        45
      • 7. Replace the lamp cover and tighten the screw.

        45
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        45
      • 9. Reset the lamp hour. Refer to the “Setting” menu.

        45
  • Specifications

    46
  • Appendix

    47
    • LED Indicator Messages

      47
    • Compatibility Modes

      48
• Computer:

  48
• Video:

  49
  • Troubleshooting

    50
• Start-up problems

  50
• Image problems

  50
  • RS-232 Command and Configuration

    51
  • IR Control Code

    53