Листовка для Insignia NS-HZ311
Installation Instructions
Installing the cable pass-through wall plate
NOTE: This product is not designed to work with DVI or VGA cables.
1 Route cables coming from the electrical box through the cable
pass-through
pass-through
panel.
NOTE: If necessary, if cables do not easily fit, the front cable cover can be
removed from the back plate by sliding the cover to the left and removing it.
The cover can be reinstalled by inserting the cover into the back plate holes
and sliding the cover to the right.
The cover can be reinstalled by inserting the cover into the back plate holes
and sliding the cover to the right.
2 Attach the cable pass-through panel to the electrical box with the
two included mounting screws.
two included mounting screws.
NOTE: If mounting the wall plate without electrical box or junction box,
please follow the below steps:
A Position the included template on the
wall where you want to mount the HDMI
wall plate. Mark the rectangular cut-out
area and mounting screw locations (A)
with a pencil and remove the template.
B Using drywall saw (not included) cut a
hole in the drywall no bigger than the
dimensions of the cut-out area of the
template.
C Using a 1/4" drill bit, drill holes in the wall
at the previously marked mounting screw locations (A).
D With a hammer gently tap the two plastic wall anchors (included)
into the holes for the mounting screw locations (A).
please follow the below steps:
A Position the included template on the
wall where you want to mount the HDMI
wall plate. Mark the rectangular cut-out
area and mounting screw locations (A)
with a pencil and remove the template.
B Using drywall saw (not included) cut a
hole in the drywall no bigger than the
dimensions of the cut-out area of the
template.
C Using a 1/4" drill bit, drill holes in the wall
at the previously marked mounting screw locations (A).
D With a hammer gently tap the two plastic wall anchors (included)
into the holes for the mounting screw locations (A).
3 Snap the pass-through panel lid to the three corresponding holes
on the cable pass-through panel.
on the cable pass-through panel.
One-year limited warranty
Visit www.insigniaproducts.com for details.
INSIGNIA is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
Registered in some countries.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
V1 ENGLISH 14-0233
Cut-out
area
area
QUICK SETUP GUIDE
Cable Pass-through Wall Plate
| NS-HZ311
This Insignia Cable Pass-through Wall Plate provides a
professional finish for in-wall cables. It is for use with a
standard electrical box through which audio/video, computer,
or other cables are routed.
professional finish for in-wall cables. It is for use with a
standard electrical box through which audio/video, computer,
or other cables are routed.
Package contents
•
Mounting
template
• Plastic wall anchors (2)
• Mounting screws (2 long screws for electrical box,
2 screws for matching with wall anchors)
• Cable pass-through panel
• Pass-through panel lid
• Quick Setup Guide
• Mounting screws (2 long screws for electrical box,
2 screws for matching with wall anchors)
• Cable pass-through panel
• Pass-through panel lid
• Quick Setup Guide
Parts required for installation (not included)
• Standard electrical box (single gang)
•
• Standard electrical box (single gang)
•
Screwdriver
If installing on wall, the following tools will also be needed:
• Drill and 1/4" drill bit
• Drywall saw (keyhole type saw with a narrow blade is
• Drill and 1/4" drill bit
• Drywall saw (keyhole type saw with a narrow blade is
recommended)
•
Hammer
NS-HZ311_14-0233_QSG_V1_EN.eps 1 2/27/2014 10:21:19 AM
NS-HZ311_14-0233_QSG_V1_EN.eps 1 2/27/2014 10:21:19 AM