Справочник Пользователя для Panasonic D11
![Panasonic](https://files.manualsbrain.com/attachments/8f677e63fb64cbb6c62d09e6242996e7631380a8/common/fit/150/50/34d700d3fb727c767799b2da5cc474b219c0a4312e9e3044c99491a2fb9a/brand_logo.png)
9
RQT5210
Listening
2
3
4
1
4
2
3
1
L
A
FM
AM
1
3
2
MEMORY/
PGM
1
2
3
Indicates auto scan
Listening to radio broadcasts
Listening to broadcast stations which have
not been programmed (Manual tuning)
not been programmed (Manual tuning)
Preparation: Set [
] to “TUNER”.
1
Press [BAND] to select “FM” or “AM”.
Every time you press the button: FM
↔
AM
2
Press [TUNE MODE] to clear the preset indicator.
The unit is set to the manual tuning mode.
3
Press [–/
g
] or [
f
/
+
] to tune in the station.
4
Adjust the volume.
RX-D11 only
When using the remote control
1.
1.
Press [BAND] to select “FM” or “AM”.
2.
Press [–/
g
] or [
f
/+] to tune in the station.
Automatic tuning:
This is a simple way of tuning in stations that have not been preset.
Keep [–/
This is a simple way of tuning in stations that have not been preset.
Keep [–/
g
] or [
f
/
+
] depressed, and release it when the frequency
display starts to change. A station with good reception is automatically
selected and the selection process then stops.
To stop automatic tuning, press [–/
selected and the selection process then stops.
To stop automatic tuning, press [–/
g
g
g
g
g
] or [
f
f
f
f
f
/
+
]
again.
Hint
Automatic tuning may stop without a station having been tuned in
when interference is encountered on neighbouring airwaves. In such
a case, tune in a station by tapping [–/
when interference is encountered on neighbouring airwaves. In such
a case, tune in a station by tapping [–/
g
g
g
g
g
] or [
f
f
f
f
f
/
+
].
Using auto scan
RX-D11 only
You can search for a station by listening to all tuned-in stations for 8
seconds each.
seconds each.
Preparation: Set [
] to “TUNER”.
(Only from the remote control)
Press [BAND] to select “FM” or “AM”.
Press [AUTO SCAN].
Auto scan starts.
Press [AUTO SCAN] when you find the desired
station.
station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To stop during the process, press [AUTO SCAN].
To turn off the unit:
Set [
Set [
] to “TAPE/
”.
If the tape is travelling, press [
L
/
c
STOP/EJECT] as well.
Adjusting the antennas A
For FM reception:
Pull out the telescopic antenna and adjust its length and angle for
optimum reception.
Pull out the telescopic antenna and adjust its length and angle for
optimum reception.
For AM reception:
Turn the unit in the direction which gives the best results.
Turn the unit in the direction which gives the best results.
Reference
Radio broadcasts may be hard to receive in a moving vehicle or in a
building because the signal may be weakened. In such cases, use the
unit near a window.
building because the signal may be weakened. In such cases, use the
unit near a window.
When there is a lot of noise in an FM stereo
broadcast
broadcast
Reduce the interference by setting the sound to monaural.
Example:
When an FM stereo program is being received;
When an FM stereo program is being received;
Press [FM MODE].
“
MONO
” is displayed.
To return to stereo reception, repeat the same procedure to turn off
the “
the “
MONO
” display.