Справочник Пользователя для Manhattan Computer Products ST100
14
4. When finished the slave receiver will reboot and come up with a channel.
TROUBLE SHOOTING GUIDE
If you suspect there is a problem with your receiver, please check the following trouble shooting guide before
calling a Manhattan authorised service agent.
If you suspect there is a problem with your receiver, please check the following trouble shooting guide before
calling a Manhattan authorised service agent.
WARNING! Do NOT attempt to repair the receiver yourself. Tampering with the receiver may
result in fatal electric shock and will invalidate your warranty.
result in fatal electric shock and will invalidate your warranty.
Symptoms --- Possible cause / solutions
Front display not lit --- Check that the mains lead is plugged into the power socket. Check that your TV is
tuned for the correct UHF channel or is switched to correct AV input.
No picture or sound or any menus --- No signal. Channel is scrambled. The antenna is not in correct
position. Check LNB wire is not damaged or shorting. Check LNB may be faulty. Unplug receiver from power
socket and retry.
Interference, on picture, using UHF output --- Local terrestrial TV interference. Change the UHF output
channel to different one then re-tune your TV. Select the appropriate ‘TV Standard’ using TV Settings menu.
Bad picture with blocking or frozen --- Signal weak or noisy. Check signal quality. Antenna not in correct
position
Not responding to remote control --- Check the batteries in your remote control. Replace with new.
You have lost or forgotten your password --- Apply master password or contact your Manhattan dealer.
Front display not lit --- Check that the mains lead is plugged into the power socket. Check that your TV is
tuned for the correct UHF channel or is switched to correct AV input.
No picture or sound or any menus --- No signal. Channel is scrambled. The antenna is not in correct
position. Check LNB wire is not damaged or shorting. Check LNB may be faulty. Unplug receiver from power
socket and retry.
Interference, on picture, using UHF output --- Local terrestrial TV interference. Change the UHF output
channel to different one then re-tune your TV. Select the appropriate ‘TV Standard’ using TV Settings menu.
Bad picture with blocking or frozen --- Signal weak or noisy. Check signal quality. Antenna not in correct
position
Not responding to remote control --- Check the batteries in your remote control. Replace with new.
You have lost or forgotten your password --- Apply master password or contact your Manhattan dealer.
SPECIFICATIONS
TUNER
Input Connector
Input Connector
F-type IEC 169-24 Female
Frequency Range
950MHz to 2150MHz
Input Impedance
75 Ohm
Signal Level
-25 to - 65 dBm
LNB Power & Polarization
Vertical +14V, Horizontal +18V (600mA Max. with Overload
Protection)
LNB Control
LNB Control
22KHz … 4 KHz, Tone burst A/B and DiSEqC 1.2
22 KHz Tone Amplitude
0.6Vpp (…0.2V)
Input Symbol Rate
2~45 Msps
FEC Decoder
Auto, 1/2, 2/3, 3/4, 5/6, 7/8
SYSTEM
Transmission Standard
Transmission Standard
DVB MPEG-2
Input Data Rate
Max 15Mb/s
Aspect Ratio
4:3, 16:9
Video Resolution
720 x 480 NTSC, 720 x 576 PAL
Audio Decoding
MPEG Layer 1 & 2
Audio Mode
Single channel / Dual Channel/Joint Stereo / Mono
Sampling Rate
32KHz, 44.1 KHz, 48 KHz, 96 KHz,
COMMON INTERFACE (optional)
Slots
Slots
2 slots type 1 and type 2
PCMCIA
DVB Common Interface Standard
IRDETO EMBEDDED CI (optional)
Card Slot
Card Slot
1 Slot
PCMCIA
DVB Common Interface Standard
CONNECTORS
RGB, CVBS
RGB, CVBS
2 SCART sockets (TV/VCR), 1 PHONO RCA
Audio Output
2 SCART sockets (TV/VCR), 2 x PHONO (L, R) / RCA
Digital Audio Output
1 PHONO RCA (S/P DIF)
Data Interface
1 RS232 (Bit Rate: 115,200 baud Connector: 9-pin D-sub type)
RF connectors
75 Ohm IEC 169-2 Male/Female
SPECIFICATIONS