Справочник Пользователя для Sony PDW-530P
Cha
p
te
r 6
F
ile O
per
at
ion
s
s
103
6-2 File Access Mode File Operations
• Deletion and renaming of directories
Notes
• File names and directory names can use letters, numbers,
and symbols from the Unicode 2.0 character set.
However, the following control characters and symbols
However, the following control characters and symbols
1)
cannot be used.
- Control characters: U+0000 to U+001F, U+007F
- Symbols: ", *, /, :, <, >, ?, \, |
- Control characters: U+0000 to U+001F, U+007F
- Symbols: ", *, /, :, <, >, ?, \, |
1) This is supported from firmware version 1.4. However, the following
character codes cannot be used by FAM connections.
U+010000, U+020000, U+030000, U+040000, U+050000,
U+060000, U+070000, U+080000, U+090000, U+0A0000,
U+0B0000, U+0C0000, U+0D0000, U+0E0000, U+0F0000,
U+100000
(There are no limits to characters which can be used by FTP
connections.)
U+010000, U+020000, U+030000, U+040000, U+050000,
U+060000, U+070000, U+080000, U+090000, U+0A0000,
U+0B0000, U+0C0000, U+0D0000, U+0E0000, U+0F0000,
U+100000
(There are no limits to characters which can be used by FTP
connections.)
6-2 File Access Mode
File Operations
File access mode operating environment
Operating system requirements for file operations by file
access mode (called FAM below) are as follows.
• Computer operating system: Microsoft Windows 2000
access mode (called FAM below) are as follows.
• Computer operating system: Microsoft Windows 2000
Service Pack 4 or higher, or Microsoft Windows XP
Preparations
Do the following on the remote computer and this unit.
• Install the FAM driver on the remote computer.
• Enable FAM connections over the i.LINK connector.
• Install the FAM driver on the remote computer.
• Enable FAM connections over the i.LINK connector.
To install the FAM driver
Insert the supplied CD-ROM (Proxy Browsing Software
PDZ-1) in the CD-ROM drive of the computer and execute
the Setup.exe file, then follow the installation instructions.
Insert the supplied CD-ROM (Proxy Browsing Software
PDZ-1) in the CD-ROM drive of the computer and execute
the Setup.exe file, then follow the installation instructions.
For details, refer to the ReadMe file contained on the CD-
ROM disc.
ROM disc.
Note
Use Version 1.4 or higher of the FAM driver. The FAM
driver on the supplied CD-ROM is Version 1.4 or higher.
If a FAM driver is already installed on your computer,
check the version.
To check the version, click “Add or Remove
Programs”(Windows XP) or “Add/Remove Programs”
(Windows 2000), select “ProDisc,” and then click “Click
here for support information.”
driver on the supplied CD-ROM is Version 1.4 or higher.
If a FAM driver is already installed on your computer,
check the version.
To check the version, click “Add or Remove
Programs”(Windows XP) or “Add/Remove Programs”
(Windows 2000), select “ProDisc,” and then click “Click
here for support information.”
To enable FAM connections over the i.LINK
connector
Proceed as follows.
connector
Proceed as follows.
1
Set the MENU ON/OFF switch to ON.
The last accessed page appears.
2
Turn the MENU knob to scroll to the OUTPUT page,
then press the MENU knob.
then press the MENU knob.
The OUTPUT page appears. The current settings
appear on the right side of each item.
appear on the right side of each item.
3
Move the
b mark to “i.LINK MODE”, then press the
MENU knob.
The
b mark changes to a z mark, and the z mark
changes to a ? mark.