Справочник Пользователя для Sony PMW-350K
Mounting and Adjusting the Lens
42
Cha
p
te
r 2
P
rep
ar
ar
at
ions
Caution
If the lens is not firmly locked, it may come off
while the camcorder is being used. This could cause
a serious accident. Make sure the lens is firmly
locked. It is recommended that the lens mount
securing rubber be put on the lens locking lever as
illustrated above.
while the camcorder is being used. This could cause
a serious accident. Make sure the lens is firmly
locked. It is recommended that the lens mount
securing rubber be put on the lens locking lever as
illustrated above.
4
Connect the lens cable to the LENS
connector.
connector.
5
Secure the lens cable with the cable
clamps.
clamps.
If you have attached an aberration correction
lens
The aberration correction function is activated
automatically. Starting the camcorder with an
aberration correction lens may require more time
than normally because of data loading at start-up.
The lens supplied with the PMW-350K is an
aberration correction lens. Contact a Sony service
representative for information about other
aberration correction lenses.
lens
The aberration correction function is activated
automatically. Starting the camcorder with an
aberration correction lens may require more time
than normally because of data loading at start-up.
The lens supplied with the PMW-350K is an
aberration correction lens. Contact a Sony service
representative for information about other
aberration correction lenses.
If the lens does not stay in focus properly as you
zoom from telephoto to wide angle, adjust the
flange focal length (the distance from the plane of
the lens mounting flange to the imaging plane).
Make this adjustment just one time after
mounting or changing the lens.
When carrying out the adjustment, use the
supplied flange focal length adjustment chart as
the subject.
zoom from telephoto to wide angle, adjust the
flange focal length (the distance from the plane of
the lens mounting flange to the imaging plane).
Make this adjustment just one time after
mounting or changing the lens.
When carrying out the adjustment, use the
supplied flange focal length adjustment chart as
the subject.
Note
If you use a subject with insufficient contrast, or
move the camcorder or subject during
adjustment, this will cause an adjustment error.
move the camcorder or subject during
adjustment, this will cause an adjustment error.
Carrying out the adjustment
When using the auto focus lens
With the lens supplied with the PMW-350K,
zoom and focus operations automatically adjust
the flange focal length.
With the lens supplied with the PMW-350K,
zoom and focus operations automatically adjust
the flange focal length.
1
Open the iris, position the supplied
flange focal length adjustment chart
approximately 3 meters (10 ft) away
from the camcorder, and arrange the
lighting to obtain a satisfactory video
output.
flange focal length adjustment chart
approximately 3 meters (10 ft) away
from the camcorder, and arrange the
lighting to obtain a satisfactory video
output.
2
Set the ZOOM switch to SERVO
(power zoom mode).
(power zoom mode).
3
Hold down the flange focal length
adjustment button for 3 seconds.
adjustment button for 3 seconds.
The flange focal length adjustment starts.
During adjustment
The message “AUTO FB EXECUTING”
appears on the viewfinder screen.
The message “AUTO FB EXECUTING”
appears on the viewfinder screen.
If the adjustment completes correctly
The message on the viewfinder screen
changes to “FB: OK”.
The message on the viewfinder screen
changes to “FB: OK”.
If the flange focal length adjustment does
not complete correctly
Check the subject and lighting conditions,
and repeat the adjustment.
not complete correctly
Check the subject and lighting conditions,
and repeat the adjustment.
When using a non-auto focus lens
1
Set the iris to manual.
2
Open the iris, position the supplied
flange focal length adjustment chart
approximately 3 meters (10 ft) away
from the camcorder, and arrange the
lighting to obtain a satisfactory video
output.
flange focal length adjustment chart
approximately 3 meters (10 ft) away
from the camcorder, and arrange the
lighting to obtain a satisfactory video
output.
3
Loosen the fixing screws on the F.f or
F.B ring (flange focal length adjustment
ring).
F.B ring (flange focal length adjustment
ring).
4
Use manual or power zoom to set the
lens to telephoto.
lens to telephoto.
5
Point the camcorder at the chart by
turning the focus ring and focus on it.
turning the focus ring and focus on it.
Adjusting the Flange Focal Length
About 3 m (10 ft)