Справочник Пользователя для Sony PMW-350K
![Sony](https://files.manualsbrain.com/attachments/7e61ba04cadfce70cb41a1a70ef1d62a30f0a5fe/common/fit/150/50/682a2570dc00831b079177f57c62a2915dd3423eb752334060fbcf750d89/brand_logo.png)
Preparing the Audio Input System
45
Cha
p
te
r 2
P
rep
ar
ar
at
ions
2
Connect the microphone cable to the
AUDIO IN CH1 or CH2 connector.
AUDIO IN CH1 or CH2 connector.
3
Set the switches as follows.
• Set the AUDIO IN selectors indicated
• Set the AUDIO IN selectors indicated
below, depending on the power supply type
of the microphone.
Internal power supply: MIC
External power supply: +48V
of the microphone.
Internal power supply: MIC
External power supply: +48V
• Set the AUDIO IN CH-1/CH-2 switch for
the channel to which the microphone is
connected to REAR.
connected to REAR.
4
Switch the input level to match the
sensitivity of the microphone used.
sensitivity of the microphone used.
Switch the input level by changing the setting of
MAINTENANCE >Audio >Rear MIC CH1/
CH2 Ref in the setup menu (factory default
setting is –60 dB). For details, see page 117.
MAINTENANCE >Audio >Rear MIC CH1/
CH2 Ref in the setup menu (factory default
setting is –60 dB). For details, see page 117.
Notes
• If the input level on the camcorder is not at an
appropriate setting for the microphone sensitivity, loud
sounds may be distorted, and the signal-to-noise ratio
may be affected.
sounds may be distorted, and the signal-to-noise ratio
may be affected.
• In order for the AUDIO IN CH1 and CH2 connectors
on the camcorder to be able to provide a phantom 48 V
power supply, female XLR connectors (3-pin) are
fitted. If the microphone cable has a female connector,
use an adaptor.
power supply, female XLR connectors (3-pin) are
fitted. If the microphone cable has a female connector,
use an adaptor.
• When you detach a CAC-12 Microphone Holder once
you have attached to the camcorder, be careful not to
lose the two screws fixing the CAC-12 (in step
lose the two screws fixing the CAC-12 (in step
1
).
After detaching the CAC-12, be sure to put the two
screws back into their original places.
screws back into their original places.
To use a Sony UHF wireless microphone system,
power the camcorder off and then fit one of the
following UHF portable tuners.
• DWR-S01D Digital Wireless Receiver
• WRR-855S UHF Synthesized Tuner Unit
• WRR-860A/861/862 UHF Synthesized
power the camcorder off and then fit one of the
following UHF portable tuners.
• DWR-S01D Digital Wireless Receiver
• WRR-855S UHF Synthesized Tuner Unit
• WRR-860A/861/862 UHF Synthesized
Diversity Tuner
For details of these units, refer to the operation
manuals for them.
manuals for them.
To fit the DWR-S01D or WRR-855S
1
Remove the four fixing screws holding
the cover of the portable tuner/receiver
housing slot located in the rear of the
camcorder, to remove the cover.
the cover of the portable tuner/receiver
housing slot located in the rear of the
camcorder, to remove the cover.
2
Insert the DWR-S01D or WRR-855S
into the housing slot, and fasten the four
fixing screws.
into the housing slot, and fasten the four
fixing screws.
1
AUDIO IN selectors
2
Monaural microphone
3
AUDIO IN CH-1/CH-2 switches
4
To AUDIO IN CH1 or CH2 connector
Attaching a UHF Portable Tuner
(for a UHF Wireless Microphone
System)
(for a UHF Wireless Microphone
System)