Справочник Пользователя для Sony 900
7
Chapter 7 Location and Function of Parts and Controls
92
HDC-900/950/930 Series Product Information Manual
7-3-6
HKCU-902 HD Analog Interface Unit
The optional HKCU-902 is designed to be installed in
the HDCU-900 expansion slot or in place of the SD
signal input/output block.
the HDCU-900 expansion slot or in place of the SD
signal input/output block.
a
RET INPUT 1-4 (return video 1, 2, 3, and 4 input)
connectors (BNC type)
connectors (BNC type)
Four different HD analog return video input signals
may be received independently. The selection of RET
1, 2, 3, or 4 is made by the camera’s return switch. The
type of input signal on RET 1, 2, 3, and 4 may be set
individually using switches on the AT board in the
HDCU-900, or using the MSU-700A/750 Master
Setup Unit.
may be received independently. The selection of RET
1, 2, 3, or 4 is made by the camera’s return switch. The
type of input signal on RET 1, 2, 3, and 4 may be set
individually using switches on the AT board in the
HDCU-900, or using the MSU-700A/750 Master
Setup Unit.
b
SYNC OUT (HD sync signal output) connector
(BNC type)
(BNC type)
Used for output of an HD tri-level sync signal from the
internal sync signal generator.
internal sync signal generator.
c
PIX OUT (HD picture monitor output) connector
(BNC type)
(BNC type)
Used for output of the picture monitor video signal
selected using the RCP-700 series Remote Control
Panel MONITOR SELECT button, or the MSU-700A/
750 Master Setup Unit PICTURE MONITOR button.
Either the Remote Control Panel or Master Setup Unit
may control the output, depending on which button
was pressed most recently.
selected using the RCP-700 series Remote Control
Panel MONITOR SELECT button, or the MSU-700A/
750 Master Setup Unit PICTURE MONITOR button.
Either the Remote Control Panel or Master Setup Unit
may control the output, depending on which button
was pressed most recently.
d
OUTPUT 1, 2 (HD analog component video 1 and
2 output) connectors (BNC type)
2 output) connectors (BNC type)
HD analog component video signals are output in
either Y, PB, PR or G, B, R format. The selection of Y,
PB, PR or G, B, R format may be made independently
for OUTPUT 1 and OUTPUT 2, using switches on the
AT board. (Factory setting: G, B, R)
either Y, PB, PR or G, B, R format. The selection of Y,
PB, PR or G, B, R format may be made independently
for OUTPUT 1 and OUTPUT 2, using switches on the
AT board. (Factory setting: G, B, R)
7-3-7
HKCU-903 Frame Rate Converter Unit
The optional HKCU-903 is to be installed in the HDCU-
900 expansion slot or in place of the SD signal input/
output block.
900 expansion slot or in place of the SD signal input/
output block.
a
SERIAL RET INPUT 1-4 (HD-SDI return video 1,
2, 3, and 4 input) connectors (BNC type)
2, 3, and 4 input) connectors (BNC type)
Four different HD-SDI return video input signals may
be received independently. The selection of RET 1, 2,
3, or 4 is made by the camera’s return switch. The type
of input signal on RET 1, 2, 3, and 4 may be set
individually using switches on the AT board in the
HDCU-900, or using the MSU-700A/750 Master Setup
Unit.
be received independently. The selection of RET 1, 2,
3, or 4 is made by the camera’s return switch. The type
of input signal on RET 1, 2, 3, and 4 may be set
individually using switches on the AT board in the
HDCU-900, or using the MSU-700A/750 Master Setup
Unit.
b
SYNC OUT (HD/SD sync signal output)
connectors (BNC type)
connectors (BNC type)
The left connector outputs a sync signal of the same
format as that of the input/output block in the above
slot. The right connector outputs the HD tri-level sync
signal of the same format as that of the SERIAL
OUTPUT 1 to 3 connectors.
format as that of the input/output block in the above
slot. The right connector outputs the HD tri-level sync
signal of the same format as that of the SERIAL
OUTPUT 1 to 3 connectors.
1
2
3
4
RET INPUT
PIX OUT
SYNC OUT
OUTPUT 1
P
R
/R
OUTPUT 2
Y/G
P
B
/B
P
R
/R
Y/G
P
B
/B
1
RET INPUT 1-4 connectors
2
SYNC OUT connector
3
PIX OUT connector
4
OUTPUT 1, 2 connectors
1
2
3
4
1
2
3
MONI
SERIAL RET INPUT
SYNC OUT
SYNC OUT
FRAME REFERENCE
SERIAL OUTPUT
IN
OUT
1
SERIAL RET INPUT 1-4 connectors
2
SYNC OUT connectors
3
FRAME REFERENCE IN/OUT connectors
4
SERIAL OUTPUT 1 to 3 and MONI connectors