Справочник Пользователя для Integra DTR-10.5
136
Using the Remote Controller with Other Components
—Continued
You can teach the DTR-10.5’s remote controller new
commands simply by transmitting commands from
another remote controller one at a time. For example, by
transmitting the Play and Stop commands from your
CD player’s remote controller, the DTR-10.5’s remote
controller can be taught to transmit those commands
commands simply by transmitting commands from
another remote controller one at a time. For example, by
transmitting the Play and Stop commands from your
CD player’s remote controller, the DTR-10.5’s remote
controller can be taught to transmit those commands
when its Play [
] and Stop [
] buttons are pressed in
CD mode.
This is convenient when you want to add commands to
buttons after entering a remote control code (See page
129).
This is convenient when you want to add commands to
buttons after entering a remote control code (See page
129).
Notes:
• The following buttons cannot be taught new com-
mands: [LIGHT], [Custom], [Macro], [Mode],
[Input], [Zone 2], [Zone 3], and the scroll wheel but-
ton.
[Input], [Zone 2], [Zone 3], and the scroll wheel but-
ton.
• The DTR-10.5’s remote controller can learn a total of
150 commands. However, the commands of some
remote controllers may use a lot of memory, in which
case, this total will be reduced.
remote controllers may use a lot of memory, in which
case, this total will be reduced.
• If the message “FULL” appears, the remote control-
ler cannot learn any more commands because its
memory is full.
memory is full.
• By default, the DTR-10.5’s remote controller knows
the commands for controlling an Integra/Onkyo CD
player, cassette deck, DVD player, and MD recorder
(e.g., Play, Stop, Pause, etc., buttons). You can teach
these buttons new commands, although the defaults
will be restored if the remote controller is reset.
player, cassette deck, DVD player, and MD recorder
(e.g., Play, Stop, Pause, etc., buttons). You can teach
these buttons new commands, although the defaults
will be restored if the remote controller is reset.
• To teach a new command to a button that has already
been taught a command, simply repeat this proce-
dure.
dure.
• Like most remote controllers, the DTR-10.5’s remote
controller uses infrared. Commands from remote
controllers that don’t use infrared cannot be learned.
controllers that don’t use infrared cannot be learned.
• When the remote controller’s batteries expire, all
learned commands will be lost and will have to be
learned all over again, so don’t discard your other
remote controllers.
learned all over again, so don’t discard your other
remote controllers.
Learning Commands from Another
Remote Controller
Remote Controller
1
Press and hold the [Custom] but-
ton for more than three seconds.
ton for more than three seconds.
The remote controller enters Custom
mode.
mode.
2
Roll the scroll wheel to select
“LEARN,” and then press the
scroll wheel.
“LEARN,” and then press the
scroll wheel.
3
Roll the scroll wheel to select the
the remote controller mode you
want to teach a new command,
and then press the scroll wheel.
the remote controller mode you
want to teach a new command,
and then press the scroll wheel.
4
On the DTR-10.5’s remote control-
ler, press the button you want to
teach the new command.
ler, press the button you want to
teach the new command.
If you press a button that cannot be
taught a new command, the message
“RETRY” appears and you should press
another button.
taught a new command, the message
“RETRY” appears and you should press
another button.
Custom
5
Point the remote controllers at
each other, about 2 to 6 inches (5–
15 cm) apart, and then, on the
other remote controller, press the
button whose command you want
to learn.
each other, about 2 to 6 inches (5–
15 cm) apart, and then, on the
other remote controller, press the
button whose command you want
to learn.
When the command has been learned
successfully, “OK” appears on the dis-
play. You may need to press the button
several times.
successfully, “OK” appears on the dis-
play. You may need to press the button
several times.
If the command is not learned success-
fully, after the message “FAIL” has been
displayed, the mode select display reap-
pears (step 3), and you should try again.
fully, after the message “FAIL” has been
displayed, the mode select display reap-
pears (step 3), and you should try again.
6
To teach the DTR-10.5’s remote
controller more new commands,
repeat steps 3 through 5.
controller more new commands,
repeat steps 3 through 5.
Press the [Custom] button when you’ve
finished.
finished.