Справочник Пользователя для Integra DTR-10.5
69
Operations
Enjoying Movies and Music in the
Remote Zone (Zone 2/3)
Remote Zone (Zone 2/3)
—
Continued
Recording a Source
The DTR-10.5 can not only record the playing source
but can also record a source while playing another
source. You can also combine a video and audio to cre-
ate a new source.
Signals that can be output to a video/audio recording
device vary with the type of jack connected. Check the
following conditions before starting recording:
but can also record a source while playing another
source. You can also combine a video and audio to cre-
ate a new source.
Signals that can be output to a video/audio recording
device vary with the type of jack connected. Check the
following conditions before starting recording:
Audio
• Signals (analog) from the ETHERNET, PH, or
AUDIO IN jacks are output only to the AUDIO OUT
jacks. Music signals of MP3, WMA, and WAVE to be
played with Net-Audio are also output only to analog
audio output jacks.
jacks. Music signals of MP3, WMA, and WAVE to be
played with Net-Audio are also output only to analog
audio output jacks.
• No signal is output from the MULTI-CH IN jacks.
• No signal is output from the HDMI IN jacks. Record-
• No signal is output from the HDMI IN jacks. Record-
ing via the HDMI OUT jack is also disabled because
Rec Out is not available in Audio Output Assign.
Rec Out is not available in Audio Output Assign.
• Signals from the DIGITAL IN OPTICAL or COAX-
IAL jacks are output to the DIGITAL OUT OPTI-
CAL or COAXIAL jacks. PCM signals are converted
into analog signals, and also output to the AUDIO
OUT jacks.
CAL or COAXIAL jacks. PCM signals are converted
into analog signals, and also output to the AUDIO
OUT jacks.
• Only PCM signals are output from the i.LINK
(AUDIO) terminals to the AUDIO OUT jacks. Digital
signals are output from the i.LINK (AUDIO) termi-
nals to the DIGITAL OUT OPTICAL or COAXIAL
jacks, but signals on Super Audio CD and DVD-
Audio are not output.
signals are output from the i.LINK (AUDIO) termi-
nals to the DIGITAL OUT OPTICAL or COAXIAL
jacks, but signals on Super Audio CD and DVD-
Audio are not output.
Video
• Video signals from the VIDEO IN, S VIDEO IN, or
COMPONENT VIDEO IN jack are output only to the
VIDEO OUT jacks.
VIDEO OUT jacks.
• When not using Zone 2 or Zone 3, press the
[Zone 2] (or [Rec/Zone 3]) button, and then
press the [Standby/On] button. Or press the
[Zone 2] (or [Rec/Zone 3]) button, and then
turn the [Select/Preset] dial to select “Off.” In
the case of Zone 2, the green indicator on the
input source button is turned off, and in the
case of Zone 3, the red indicator is turned off.
press the [Standby/On] button. Or press the
[Zone 2] (or [Rec/Zone 3]) button, and then
turn the [Select/Preset] dial to select “Off.” In
the case of Zone 2, the green indicator on the
input source button is turned off, and in the
case of Zone 3, the red indicator is turned off.
• When operating in the main room, be sure to
confirm that the [Standby] indicator is not
blinking, and then start operations. When not
using in the main room, press the [Standby/
On] button. If the DTR-10.5 is in the standby
status, the power supply to Zone 2 and Zone 3
is not switched off.
blinking, and then start operations. When not
using in the main room, press the [Standby/
On] button. If the DTR-10.5 is in the standby
status, the power supply to Zone 2 and Zone 3
is not switched off.