Справочник Пользователя для Integra DTR-10.5

 

94

 

Follow procedures below to change any setting:

 

When you perform the procedures on the DTR-10.5, 
after selecting the input source using the input source 
buttons, press the [Setup] button. Next, select the menu 
you want to configure by turning the [Select/Preset] dial 
and press the dial to confirm the selection. Then, after 
selecting the sub-menu you want to configure by 
turning the [Select/Preset] dial, select your value by 
turning the [Control/Tuning] dial, and press the dial to 
confirm the value. If you want to go back to the 
previous operation, press the [Exit] button. 

 

In assignment of a DVD recorder to input of VIDEO 1, 
when the analog audio input is connected to “VIDEO 
1,” the digital audio to “COAXIAL 2,” and the video to 
“S VIDEO 2” and “COMPONENT 2.” 
1. Press the [Input] button, and then roll the scroll 

wheel to select “VIDEO 1.”

2. Press the scroll wheel, and then press the [Setup] 

button to display the Main Menu.

3. Use the [

]/[

] buttons to select “Input Setup,” 

and then press the [Enter] button. 

4. Use the [

]/[

] buttons to select “Audio Assign” 

from the sub-menu, and then press the [Enter] button. 

5. Use the [

]/[

] buttons to select “Analog Audio,” 

and then use the [

]/[

] buttons to select “1.” 

6. Use the [

]/[

] buttons to select “Digital Audio,” 

and then use the [

]/[

] buttons to select “Coax 2.” 

7. Press the [Return] button to return to the sub-menu. 
8. Use the [

]/[

] buttons to select “Video Assign,” 

and then press the [Enter] button. 

9. Use the [

]/[

] buttons to select “S-Video,” and 

then use the [

]/[

] buttons to select “2.” 

10. Use the [

]/[

] buttons to select “Component 

Video,” and then use the [

]/[

] buttons to select 

“RCA 2.” 

11. Press the [Setup] button. 

Setting is completed and the menu screen disap-
pears. 

The following are settings for audio. When input is 
“NET AUDIO,” see the following page.

 

The following are settings for analog audio output: 

 

Select the device connected to “AUDIO IN PH.” 

 

 Select the device connected to the jack of “AUDIO 

IN 1-9.” 

 

Select the device connected to the “Video 7 

Input L-Audio-R” jack behind the front door of the 
DTR-10.5.

 

Select this when no device is connected. 

 

This item appears when the multichannel terminal 
board [E] is inserted. When the multichannel terminal 
board contains a single set of multichannel terminals, 
available options are “1” and “No.”

 

 Select the device connected to the jack of “MULTI-

CH IN 1.” 

 

Select the device connected to the jack of “MULTI-

CH IN 2.” This item is available when a multichannel 
option board with two multichannel terminal sets is 
installed.

 

 Select this when no device is connected. 

 

This item appears when the multichannel terminal 
board [E] is inserted.
The following are settings for “Multichannel 1” or 
“Multichannel 2” described above, and cannot be 
specified separately for each input source. For example, 
when the input source is CD and “Surround Back 
Channel” is set to “Not Used (5.1 ch)” for 
“Multichannel 1,” switching the input source to DVD 
and “Surround Back Channel” to “SBL/SBR (7.1ch)” 
will also change “Surround Back Channel” associated 
with CD to “SBL/SBR (7.1ch).”

 

 Select this when not using the 

surround back channel. 

 

Select this when using 

the surround back channel.

 

The Main Menu appears onscreen. 

 

The sub-menu is displayed. 

 

Other items should be selected in the same way. 

 

The display returns to the sub-menu. 

 

When all of the items are set, go to procedure 7. 

 

Settings are completed and the menu screen disappears.

 2.Input Setup
    ==Input:XXXXXX=======
  
  1.Audio Assign
  2.Video Assign
  3.Listening Mode Preset
  4.Character Edit
  5.IntelliVolume
  6.Delay
  7.Picture Setting
  8.12V Trigger Assign