Справочник Пользователя для Integra DHC-9.9
57
For AM tuning to work properly, you must specify the
AM frequency step used in your area. Note that when
this setting is changed, all radio presets are deleted.
AM frequency step used in your area. Note that when
this setting is changed, all radio presets are deleted.
Note:
This procedure can also be performed on the AV control-
ler by using its [Setup] button, arrow buttons, and [Enter]
button.
This procedure can also be performed on the AV control-
ler by using its [Setup] button, arrow buttons, and [Enter]
button.
If you connect an
u-capable Onkyo MiniDisc
recorder, CD recorder, or RI Dock to the TAPE IN/OUT
jacks, or connect an RI Dock to the AUX 1 jacks, for
jacks, or connect an RI Dock to the AUX 1 jacks, for
u
to work properly, you must change this setting.
This setting can only be changed on the AV controller.
Note:
DOCK can be selected for the Tape input selector or
AUX 1 input selector, but not both at the same time.
DOCK can be selected for the Tape input selector or
AUX 1 input selector, but not both at the same time.
AM Frequency Step Setup
(on some models)
(on some models)
1
Press the [Receiver] button, fol-
lowed by the [Setup] button.
The main menu appears onscreen.
lowed by the [Setup] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w] but-
tons to select “7. Hardware
Setup”, and then press [Enter].
The “Hardware Setup” menu appears.
Setup”, and then press [Enter].
The “Hardware Setup” menu appears.
3
Use the Up and Down [
q]/[w] but-
tons to select “3. Tuner”, and
then press [Enter].
The “Tuner” menu appears.
then press [Enter].
The “Tuner” menu appears.
4
Use the Up and Down [
q]/[w] but-
tons to select “AM Freq Step”,
and then use the Left and Right
[
and then use the Left and Right
[
e]/[r] buttons to select:
10kHz: Select if 10 kHz steps are
used in your area.
9kHz: Select if 9 kHz steps are used
in your area.
Receiver
Setu
p
Enter
Enter
7. Hardware
Setup
1. Remote
Control
2. Zone2/Zone3
3. Tuner
4. Analog
3. Tuner
4. Analog
Multich
5. HDMI
6. Network
6. Network
MOVE
ENTER
RETURN
ENTER
RETURN
EXIT
SETUP
Enter
Enter
7–3. Tuner
AM Freq Step
9kHz
VALUE
RETURN
RETURN
EXIT
SETUP
Enter
Enter
5
Press the [Setup] button.
Setup closes.
Setup closes.
Changing the Input Display
1
or
Press the [Tape] or [AUX 1] input
selector button so that “TAPE” or
“AUX1” appears on the display.
selector button so that “TAPE” or
“AUX1” appears on the display.
2
(3 seconds)
or
(3 seconds)
Press and hold down the [Tape]
or [AUX 1] input selector button
(about 3 seconds) to change the
setting.
Repeat this step to select MD, CDR, or
DOCK.
or [AUX 1] input selector button
(about 3 seconds) to change the
setting.
Repeat this step to select MD, CDR, or
DOCK.
For the Tape input selector, the setting
changes in this order:
changes in this order:
For the AUX 1 input selector, the set-
ting changes in this order:
ting changes in this order:
AUX1
↔
DOCK
Setu
p
1, 2 1, 2
TAPE
→
MD
→
CDR
DOCK
→
→