Справочник Пользователя для Crown Audio IT9000 HD
I-Tech HD Series Power Amplifi ers
Operation Manual
page 7
2.2 Connecting to AC Mains
WARNING: The third (ground) prong of the supplied AC power
cord connector is a required safety feature. Do not attempt to
disable this ground connection by using an adapter or other
methods.
cord connector is a required safety feature. Do not attempt to
disable this ground connection by using an adapter or other
methods.
Amplifi ers don’t create energy. The AC mains voltage and current must be
suffi cient to deliver the power you expect. You must operate your amplifi er
from an AC mains power source with not more than a 10% variation above
or a 15% variation below the amplifi er’s specifi ed line voltage range and
within the specifi ed frequency requirements (indicated on the amplifi er’s
back panel label). If you are unsure of the output voltage of your AC mains,
please consult your electrician.
suffi cient to deliver the power you expect. You must operate your amplifi er
from an AC mains power source with not more than a 10% variation above
or a 15% variation below the amplifi er’s specifi ed line voltage range and
within the specifi ed frequency requirements (indicated on the amplifi er’s
back panel label). If you are unsure of the output voltage of your AC mains,
please consult your electrician.
Packed with your I-Tech amplifi er is a clip that retains the power cord so it
can’t pull out accidentally.
can’t pull out accidentally.
1. Locate the clip in a bag in the I-Tech packing carton.
2. Locate the IEC power connector on the back of the amplifi er. Above and
below that connector are two slots. Stretch the ends of the clip and insert
them into the slots (Figure 2.3).
below that connector are two slots. Stretch the ends of the clip and insert
them into the slots (Figure 2.3).
3. Plug the power cord all the way into the amplifi er IEC power connector.
4. Pull the clip to the left and snap it onto the power cord.
2.3 Wire Inputs and Outputs
2.3.1 Wiring basics
• Always use shielded wire for input wiring. The higher the density of the
shield (the outer conductor) the better. Spiral wrapped shield is not
recom mended.
• When using unbalanced lines keep the cables as short as possible. Avoid
lengths greater than 10 feet (3 meters).
• Do not run the audio input cables together with the high-level wiring such
as loudspeaker wires or AC cords. (This lessens the chance of hum and
noise being induced into the input cables.)
• Turn the entire sound system off before changing any connections.
Crown is not liable for damage incurred when any transducer or compo nent
is overdriven.
shield (the outer conductor) the better. Spiral wrapped shield is not
recom mended.
• When using unbalanced lines keep the cables as short as possible. Avoid
lengths greater than 10 feet (3 meters).
• Do not run the audio input cables together with the high-level wiring such
as loudspeaker wires or AC cords. (This lessens the chance of hum and
noise being induced into the input cables.)
• Turn the entire sound system off before changing any connections.
Crown is not liable for damage incurred when any transducer or compo nent
is overdriven.
THE CHANNEL 2 INPUT IS IGNORED by default in Bridge Mono mode. It
can be summed using the input source selector and used instead of
Channel 1.
can be summed using the input source selector and used instead of
Channel 1.
For additional information on audio input wiring please refer to the Crown
Amplifi er Application Guide available online at www.crownaudio.com. It
contains helpful information on preventing unwanted subsonic frequen cies,
radio frequency interference, ground loops, and feedback oscillation.
Amplifi er Application Guide available online at www.crownaudio.com. It
contains helpful information on preventing unwanted subsonic frequen cies,
radio frequency interference, ground loops, and feedback oscillation.
When using network connections, pass the CAT 5 cable fi ve times through a
ferrite core (Figure 2.4), available from Crown Audio Inc. This is to ensure
compliance with emission regulations.
ferrite core (Figure 2.4), available from Crown Audio Inc. This is to ensure
compliance with emission regulations.
2 Setup
Figure 2.3 IEC Power Connector Clip
IEC Power Connector
Slot
Slot
Clip
Figure 2.4 Pass the CAT 5 Cable Five Times Through the Ferrite Core