Справочник Пользователя для Philips MCD700
31
English
Radio Reception
Tuning to radio stations
1
Press
STANDBY ON
y (or y on the remote)
to switch on the last selected source.
2
Press
SOURCE (or TUNER on the remote)
to select TUNER mode.
3
Press
BAND/
9 (or TUNER on the remote)
again to select the desired band: FM or AM.
4
Press and hold the control knob to the left/right
(corresponding to
(corresponding to
S
/
T
) or
TU +/-
à /
á on the remote until the frequency indication
starts to change, then release.
starts to change, then release.
➜
The system automatically tunes to the next
strong radio station.
●
To tune to a weak station, press the control
knob to the left/right (corresponding to
knob to the left/right (corresponding to
S
/
T
) or
TU +/-
à / á on the remote
briefly and repeatedly until an optimal reception
is found.
is found.
5
Repeat Step 4 if necessary until you find the
desired radio station.
desired radio station.
Presetting radio stations
You can preset up to 40 stations (20 in each
band) regardless of the reception.
band) regardless of the reception.
1
Tune to your desired radio station (refer to
“Tuning to radio stations”).
“Tuning to radio stations”).
2
Press the control knob upward (corresponding
to
to
PROGRAM) or press PROG on the
remote.
➜
”
PROG” icon flashes.
3
Press
CH +/- (
¡ / ™) or use the Numeric
Keypad (0-9) on the remote to select the
desired preset number.
desired preset number.
➜
If “
PROG” icon goes off before you select the
desired preset number, press the control knob
upward (corresponding to
upward (corresponding to
PROGRAM) or press
PROG on the remote.
4
Press the control knob upward (corresponding
to
to
PROGRAM) or press PROG on the
remote again to store the radio station.
●
Repeat steps 1-4 to store other radio stations.
Other Functions
Listening to preset radio stations
●
In tuner mode, press
PRESET/
ÉÅ (or CH
+/- (
¡ / ™) on the remote) or use the
Numeric Keypad (0-9) to select the desired
preset number.
preset number.
➜
The preset number, radio frequency, and
waveband are displayed.
Setting the clock
1
In Standby mode, press and hold
CLOCK on
the remote until the time flashes on the display.
➜
”
CLOCK SET” is displayed briefly. Then, the
hour digits flash on the display screen.
2
Turn
VOLUME -/+ clockwise or anticlockwise
or press
VOLUME +/- on the remote to set
the hours.
3
Press
CLOCK to confirm.
➜
The minute digits flash on the display screen.
4
Turn
VOLUME -/+ clockwise or anticlockwise
or press
VOLUME +/- on the remote to set
the minutes.
5
Press
CLOCK again to confirm the clock
setting.
Notes:
– This system only supports 24-hour mode.
– The clock setting will be erased when the
system is disconnected from the power supply.
– The system will exit clock setting mode if no
button is pressed within 30 seconds.
– This system only supports 24-hour mode.
– The clock setting will be erased when the
system is disconnected from the power supply.
– The system will exit clock setting mode if no
button is pressed within 30 seconds.
Setting sleep/wake-up timer
Sleep timer setting
In power-on mode, the sleep setting enables
the system to switch to standby mode
automatically at a preset time.
the system to switch to standby mode
automatically at a preset time.
1
In power-on mode, press
SLEEP/TIMER on
the remote repeatedly to select a preset time.
➜
The selections are as follows (time in
minutes):
00
00
➜ 10 ➜ 20 ➜ 30 ➜ 40 ➜ 50 ➜ 60 ➜ 70
➜ 80 ➜ 90 ➜ 00
2
When you reach the desired length of time,
stop pressing
stop pressing
SLEEP/TIMER.
➜
”
SLEEP” appears.
pg001-038_MCD700_37_Eng
2005.10.28, 13:31
31