Справочник Пользователя для Jensen vm9311ts

5

VM9311TS

1.

Press the metal levers on both sides to remove the half-
sleeve from the radio.

2.

Install the half-sleeve.

a. Install adapter if necessary (optional).
b. Install half-sleeve into adapter or dashboard (use only 

the supplied screws). Do not force the sleeve into the 
opening or cause it to bend or bow.

c. Locate the series of bend-tabs along the top, bottom 

and sides of the mounting sleeve. With the sleeve fully 
inserted into the dashboard opening, bend as many of 
the tabs outward as necessary so that the sleeve is 
firmly secured to the dashboard.

d. Install support strap to make the unit more stable.

CAUTION! Be careful not to damage the car 

wiring.

3.

Place the radio in front of the dashboard opening so the 
wiring can be brought through the mounting sleeve.

Complete wiring as illustrated in the wiring diagram on page 
3. Once the wiring is complete, reconnect the battery 
negative terminal. If there is no ACC available, connect the 
ACC lead to the power supply with a switch.

NOTE: When replacing a fuse, be sure to use 

correct type and amperage to avoid damaging 

the radio. The VM9311TS uses one 10 amp mini-

ATM fuse, located in the black filter box in-line 

with the main wire harness.

After completing the wiring connections, turn the unit on to 
confirm operation (ignition switch must be on). If unit does not 
operate, recheck all wiring until problem is corrected. Once 
proper operation is achieved, turn off the ignition switch and 
proceed with final mounting of the chassis.

1.

Connect wiring adapter to existing wiring harness.

2.

Connect antenna lead.

3.

Carefully slide the radio into the half-sleeve, making 
sure it is right-side-up, until it is fully seated and the 
spring clips lock it into place.

NOTE: For proper operation of the CD/DVD player, 

the chassis must be mounted within 20° of 

horizontal. Make sure the unit is mounted within 

this limitation. 

4.

Attach one end of the perforated support strap 
(supplied) to the screw stud on the rear of the chassis 
using the hex nut provided. Fasten the other end of the 
perforated strap to a secure part of the dashboard either 
above or below the radio using the screw and hex nut 
provided. Bend the strap to position it as necessary. 

CAUTION! The rear of the radio must be 

supported with the strap to prevent damage to 

the dashboard from the weight of the radio or 

improper operation due to vibration.

5.

Replace any items you removed from the dashboard.

1.

Remove trim ring.

2.

Mount factory brackets on new radio using existing 
screws from old radio.

3.

Slide radio chassis into dash opening and secure.

4.

Reinstall dash panel.

The iAUX

3

 (sold separately) allows you to connect a variety 

of external devices, including a VCR, DVD player, portable 
MP3 player, etc., to your VM9311TS without removing the 
radio.

To install the iAUX

3

, connect it to the AUX-IN cables on the 

back of the VM9311TS (see the Wiring Diagram on page 3), 

and then install the iAUX

3

 in a location convenient for 

plugging in auxiliary devices.

7-INCH

TFT

7-INCH

TFT

SRC

VM9311TS

AS

BAND

DISP

POWER

ENTER

AM/FM/DVD/MP3

RECEIVER

7-INCH

DIGITAL

TFT

OPEN

Push

VOL

MUTE

SCN

RPT

RDM

STOP

LO/DX

7-INCH

TFT

7-INCH

TFT

MODE

VM9510

MUTE

AS/PS

BAND

DISP

PWR

ENTER

AM/FM/DVD/MP3

RECEIVER

7-INCH

DIGITAL

TFT

OPEN

Push

Push

AV AUX

IN

7-INCH

TFT

7-INCH

TFT

MODE

VM9510

MUTE

AS/PS

BAND

DISP

PWR

ENTER

AM/FM/DVD/MP3

RECEIVER

7-INCH

DIGITAL

TFT

OPEN

Push

Push

AV AUX

IN