Справочник Пользователя для Ingersoll-Rand 2-1/2
2
! "#
CYLINDER
1-1/2” BORE
2” BORE
2-1/2” BORE
3-1/4” BORE
4” BORE
TYPE
HEAD
CAP
HEAD
CAP
HEAD
CAP
HEAD
CAP
HEAD
CAP
NON-CUSHIONED
119462
119471
119480
119489
119498
119507
119516
119525
119534
119543
CUSHIONED
119651
119666
119654
119669
119657
119672
119660
119675
119663
119678
NON-CUSHIONED MS4
119464
119473
119482
119491
119500
119509
119518
119527
119536
119545
CUSHIONED MS4
119652
119667
119655
119670
119658
119673
119661
119676
119664
119679
NON-CUSHIONED TRUNNION
119901
119902
119903
119904
119905
119906
119907
119908
119909
119910
CUSHIONED TRUNNION
119653
119668
119656
119671
119659
119674
119662
119677
119665
119680
!6! "(.&6!$* $7 $5 46,5
119752
119754
119756
119758
119760
119762
119764
119766
119768
119770
CUSHIONED FEM. RET. BOLT
114063
114064
114065
114066
114067
114068
114069
114070
114071
114072
!6! "(.&6!$* $7 $5 46,5 7
119835
119836
119839
119840
119843
119844
119847
119848
119851
119852
"(.&6!$* $7 $5 46,5 7
119877
119878
119879
119880
119881
119882
119883
119884
119885
119886
BORE
SIZE
SPACER
“A”
“B”
CAP SCREW
g
TORQUE
(FT LBS)
1-1/2”
119577-150
.375”
2.000”
1/4” - 28 x 2-1/4”
9
2”
119577-200
.375”
2.500”
5/16” - 24 x 2-1/4” (Low Head)
16
2-1/2”
119577-250
.375”
3.000”
5/16” - 24 x 2-1/4” (Low Head)
21
3-1/4”
119577-325
.625”
3.750”
3/8” - 24 x 2-3/4”
35
4”
119577-400
.625”
4.500”
3/8” - 24 x 2-3/4”
49
Q
When used with MF1 flange, spacer 119577-( ) is mounted between head and flange and requires 4 mounting screws of
the size listed in the table.
the size listed in the table.
Q
When used without MF1 flange, spacer 119577-( ) is slid over piston rod and bushing, against cylinder head. No new mount-
ing screws are required. Spacer is attached using Loctite or “superglue”.
ing screws are required. Spacer is attached using Loctite or “superglue”.
CYLINDER TYPE
A - Double Acting, Single Rod End
B - Double Acting, Double Rod End
RKN
X
X
X
X
B
PROVENAIR SEAL KITS
BORE SIZE
Q - 1-1/2”
5 - 5”
S - 2”
6 - 6”
T - 2-1/2”
8 - 8”
W - 3-1/4”
Y - 10”
4 - 4”
ROD DIAMETER
K - 5/8”
Q - 1-3/4”
M - 1”
S - 2”
P - 1-3/8”
SEALS
B - Nitrile; Nitrile, Mag
S - Self-Lube; Self-Lube, Mag
V - Viton; Viton, Mag
NOTE: All seal kits include wear strip and cushion seals.
HEADS AND CAPS
CUSHIONED BOTH ENDS
119577-( ) SPACER INSTALLATION
To replace tie rod cylinders that have end caps made from castings (such as Wabco, Taiyo and Aro series 38 / 39), use
spacers as called out below.
“A”
“B”
“B”
Q
Spacer
Mounting Screw for MF1 mount (4 req’d)
g
MF1 Head Flange
Cylinder Head
g
Not Supplied