Дополнительное Руководство для Hafler se120
SPECIFICATIONS
POWER RATING:
Less than 0.006% total harmonic distortion at any
power level up to 60 watts continuous average power per
channel into 8 ohms at any frequency between 20 Hz and
20 kHz with both channels driven.
channel into 8 ohms at any frequency between 20 Hz and
20 kHz with both channels driven.
IM DISTORTION (IHF):
Less than 0.005% from 1 to 60 watts, each channel,
into 8 ohms.
TYPICAL THD AT 60 WATTS INTO 8 OHMS:
20 Hz: 0.002%
1 kHz: 0.002%
20 kHz: 0.006%
FREQUENCY RESPONSE INTO 8 OHMS:
-3dB, 4Hz to 2OOkHz at 1 watt.
+OdB, -0.5dB, 1OHz to 4OkHz at 60 watts.
TYPICAL CHANNEL SEPARATION:
2OHz: > 75dB
1kHz: > 85 dB
20kHz: > 65dB
SIGNAL TO NOISE RATIO, UNWEIGHTED:
Exceeds 1OOdB referred to 60 watts into 8 ohms.
INPUT IMPEDANCE: 22,000 ohms
INPUT SENSITIVITY:
1.1 volts rms for 60 watts into 8 ohms.
DAMPING FACTOR:
100 to 1kHz into 8 ohms, 50 to 1OkHz into 8 ohms.
POWER CONSUMPTION:
60 watts both channels into 8 ohms: 300 VA
Quiescent: 60 VA
60 watts both channels into 8 ohms: 300 VA
Quiescent: 60 VA
SIZE: 3-1/4” high plus 1/2” feet, 17” wide, 9” deep.
(83 mm high plus 152 mm, 432 mm wide,
229 mm deep.)
229 mm deep.)
NET WEIGHT: 18 lbs. (8.2 kg)
SHIPPING WEIGHT: 20 lbs. (9.1 kg)
Stereo/Mono Channel Operation:
The SE120 delivers 60 watts continuous average power per
channel into 8 ohms. It can be bridged for single channel
operation producing up to 120 watts of power into 16 ohms.
operation producing up to 120 watts of power into 16 ohms.
Input Mode Selector:
This switch will allow the user to specify the input signal to
the amplifier.
This switch will allow the user to specify the input signal to
the amplifier.
A. Stereo Mode:
This allows the right and left channels to reach their
designated amplifier channels. This mode will deliver
more than 60 watts into an 8 ohm load.
B. Mono Mode:
The SE1 20 can be operated in a bridged mode which drives
both channels with the same signal and combines to deliver
more than 150 watts into 8 ohms. This disables the right
channel input and routes the signal through the left channel.
The SE1 20 can be operated in a bridged mode which drives
both channels with the same signal and combines to deliver
more than 150 watts into 8 ohms. This disables the right
channel input and routes the signal through the left channel.
Construction:
The simplified construction of the SE120 improves relia-
bility and results in consistent performance. The heavy
bility and results in consistent performance. The heavy
duty case construction on the SE120 will provide years of
durability and trouble free protection.
durability and trouble free protection.
Gold Plated RCA Input Connectors:
This provides the most accurate signal transmission and
lowest possible loss. Gold-plated terminals are immune to
signal deterioration with time that can be caused by corro-
sion in the connectors.
sion in the connectors.
Speaker Output and Power Connectors:
For minimum loss power transfer, high definition and
oxidization resistance.
For minimum loss power transfer, high definition and
oxidization resistance.
Protection System:
The SE120 is equipped with a unique protection system
that constantly monitors the temperature of the output
devices and takes corrective action to prevent damage to
the amplifier as a result of excessive overheating.
the amplifier as a result of excessive overheating.
ALL SPECIFICATIONS SUBJECT TO CHANGE
WITHOUT NOTICE.
WITHOUT NOTICE.
Copyright
1990. All rights reserved
-l-