Справочное Руководство для Amana 41480 2" 2-flute super plunge bit - 1
5
ROUTER BITS
Products shown in Bold indicate most popular items.
PLYWOOD/METRIC/SHEAR BITS
Application: Excellent
for cutting composition
board and melamine. Used
board and melamine. Used
primarily in production overhead routing, but may
be used in a hand-held application. ‘Down-
Shear’ causes chips to expel away from the
router. Not intended to be used ‘inverted’, as in a
router table or shaper.
be used in a hand-held application. ‘Down-
Shear’ causes chips to expel away from the
router. Not intended to be used ‘inverted’, as in a
router table or shaper.
PRODUCTION SHEAR
Tool No.
D
B
d
L
45414-PS
3/8
1
1/2
2-3/4
45420-PS
1/2
1-1/4
1/2
2-7/8
45422-PS
1/2
1-1/2
1/2
3-1/8
45426-PS
1/2
2
1/2
4-1/4
d
L
B
D
2 FLUTE STRAIGHT PLUNGE
Application: For precision dado cuts in
plywood, melamine, MDF, flakeboard and other
sheet materials where standard size bits are too
large. Available in fractional and metric sizes.
sheet materials where standard size bits are too
large. Available in fractional and metric sizes.
FRACTIONAL SIZES
L
B
D
d
2 FLUTE STRAIGHT PLUNGE
3˚ DOWN-SHEAR
3˚ DOWN-SHEAR
Actual
Tool No.
D
Plywood Thickness
B
d
L
45219
10MM
– 19MM
1/4
2-1/8
45417
10MM
– 19MM
1/2
2-1/2
45221
10.3MM
– 19MM
1/4
2-1/8
45240
12MM
12MM
3/4
1/4
2
45488
12MM
12MM
1-1/4
1/2
2-7/8
* 45225
14MM
– 19MM
1/4
2-1/8
* 45431
14MM
– 25MM
1/2
2-5/8
45248
16MM
16MM
3/4
1/4
2
45492
16MM
16MM
1-1/4
1/2
2-7/8
45256
18MM
18MM
3/4
1/4
2
45498
18MM
18MM
1-1/4
1/2
2-7/8
* 14MM bits for cutting plastic pilaster.
NOTE: Many standard metric plunge bits from 3MM through 51MM
are available on special order. Please allow 2 to 3 weeks for
delivery. Also, see above for metric sized plywood bits.
NOTE: Many standard metric plunge bits from 3MM through 51MM
are available on special order. Please allow 2 to 3 weeks for
delivery. Also, see above for metric sized plywood bits.
NOTE: For 6MM board, use #45203 (15/64) shown in fractional
section above. For oversized bits see page 3.
section above. For oversized bits see page 3.
Actual
Tool No.
D
Plywood Thickness
B
d
L
45203
15/64
1/4 minus 1/64 (6.0MM)
3/4
1/4
2
45206
7/32
1/4 minus 1/32
3/4
1/4
2
45223
15/32
1/2 minus 1/32
3/4
1/4
2
45425
15/32
1/2 minus 1/32
1-1/4
1/2
2-7/8
45238
19/32
5/8 minus 1/32
3/4
1/4
2
45437
19/32
5/8 minus 1/32
1-1/4
1/2
2-7/8
45231
23/32
3/4 minus 1/32
3/4
1/4
2
45445
23/32
3/4 minus 1/32
1-1/4
1/2
2-7/8
NOTE: For oversized bits, see page 3.
Application: Same as down-shear listed
above, but with up-shear design to pull chips
away from the cut. Can be used inverted as in
a router table or shaper. Straight ground (not
away from the cut. Can be used inverted as in
a router table or shaper. Straight ground (not
radial ground) for highest
quality cut and fastest feed
rate.
quality cut and fastest feed
rate.
PRODUCTION SHEAR
Tool No.
a°
D
B
d
L
42440
4°
3/8
1
1/2
2-3/4
42444
7°
1/2
1
1/2
2-3/4
42448
6°
1/2
1-1/4
1/2
2-7/8
42452
5°
1/2
1-1/2
1/2
3-1/8
42456
4°
1/2
2
1/2
4-1/4
42460
8°
3/4
1-1/4
1/2
2-7/8
42472
8°
3/4
1-1/4
3/4
3-1/4
42476
5°
3/4
2
3/4
4
42464
10°
1
1-1/4
1/2
2-7/8
d
L
B
D
a
°
2 FLUTE STRAIGHT PLUNGE
UP-SHEAR DESIGN
UP-SHEAR DESIGN
STRAIGHT PLUNGE CUTTING
METRIC SIZES • 2 FLUTE
d
D
B
L
2 FLUTE
STAGGERED SHEAR TOOTH
STAGGERED SHEAR TOOTH
‘OPPOSITE-SHEAR’
L
B
d
D
Application:
Unique design for
plunge and route
operations and
trimming of double-
sided melamine,
plywood, laminate
and veneer.
Particularly suitable
for sink cut-outs, doors, etc. Also works
well for solid surface materials.
plunge and route
operations and
trimming of double-
sided melamine,
plywood, laminate
and veneer.
Particularly suitable
for sink cut-outs, doors, etc. Also works
well for solid surface materials.
Tool No.
D
B
d
L
51320
1/2
1-1/2
1/2
3-1/8
51324
1/2
2
1/2
4-1/8
UNDERSIZED PLYWOOD
DADO
DADO