Инструкция С Настройками для Olympus TG-810
63
EN
Usage Tips
Usage Tips
If the camera does not work as intended, or if an error
message is displayed on the screen, and you are unsure
of what to do, refer to the information below to fi x the
problem(s).
message is displayed on the screen, and you are unsure
of what to do, refer to the information below to fi x the
problem(s).
Troubleshooting
Battery
Battery
“The camera does not work even when batteries are
installed”.
installed”.
Insert recharged batteries in the correct direction.
“Inserting the battery” (p. 14), “Charging the battery
and setting up using the supplied CD” (p. 14),
“Charging the battery with the included USB-AC
adapter” (p. 17)
Battery performance may have been reduced
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
“Inserting the battery” (p. 14), “Charging the battery
and setting up using the supplied CD” (p. 14),
“Charging the battery with the included USB-AC
adapter” (p. 17)
Battery performance may have been reduced
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
Card/Internal memory
Card/Internal memory
“An error message is displayed”.
“Error message” (p. 64)
Shutter button
Shutter button
“No picture is taken when the shutter button is pressed”.
Cancel sleep mode.
To save battery power, the camera automatically goes
into sleep mode and the monitor turns off if there is
no operation for 3 minutes when the camera is turned
on. No picture is taken even if the shutter button is
fully pressed in this mode. Operate any button except
for the zoom buttons to restore the camera from sleep
mode before taking a picture. If the camera is left for
another 12 minutes, it automatically turns off. Press
the n button to turn the camera on.
Press the
To save battery power, the camera automatically goes
into sleep mode and the monitor turns off if there is
no operation for 3 minutes when the camera is turned
on. No picture is taken even if the shutter button is
fully pressed in this mode. Operate any button except
for the zoom buttons to restore the camera from sleep
mode before taking a picture. If the camera is left for
another 12 minutes, it automatically turns off. Press
the n button to turn the camera on.
Press the
q button to switch to the shooting
mode.
Wait until
Wait until
#(fl ash charge) stops blinking before
taking pictures.
●
●
●
●
●
With prolonged camera use, the internal temperature
may increase, resulting in automatic shutdown. If this
occurs, remove the battery from the camera and wait
until the camera has suffi ciently cooled. The camera’s
external temperature may also increase during use,
however this is normal and does not indicate malfunction.
may increase, resulting in automatic shutdown. If this
occurs, remove the battery from the camera and wait
until the camera has suffi ciently cooled. The camera’s
external temperature may also increase during use,
however this is normal and does not indicate malfunction.
Monitor
Monitor
“Diffi cult to see”.
Condensation
*1
may have occurred. Turn off the
power, and wait for the camera body to become
acclimated to the surrounding temperature and dry
out before taking pictures.
acclimated to the surrounding temperature and dry
out before taking pictures.
*1
Dew drops can form in the camera when it is
suddenly taken from a cold location into a warm,
humid room.
humid room.
“Vertical lines appear on the screen”.
This condition may occur when the camera is
pointed at an extremely bright subject under a clear
sky and so on. The lines do not appear, however,
in the fi nal image.
pointed at an extremely bright subject under a clear
sky and so on. The lines do not appear, however,
in the fi nal image.
“The light is caught in the picture”.
Shooting with fl ash results in an image with many
fl ash refl ections on dust in the air.
fl ash refl ections on dust in the air.
Date and time function
Date and time function
“Date and time settings return to the default setting”.
If the batteries are removed and left out of the
camera for about 3 days
camera for about 3 days
*2
, the date and time settings
return to the default setting, and must be reset.
*2
The time until the date and time settings return to
the default setting varies depending on how long
the batteries have been loaded.
the batteries have been loaded.
“Date, time, time zone, and language” (p. 18)
Miscellaneous
Miscellaneous
“The camera makes a noise when taking pictures”.
The camera may activate the lens and make a
noise even if no operation is performed. This
is because the camera automatically performs
actions of auto focus as far as it is ready to shoot.
noise even if no operation is performed. This
is because the camera automatically performs
actions of auto focus as far as it is ready to shoot.
●
●
●
●
●
●