Инструкции Пользователя для NAD C 516BEE

The C 516BEE can play back CD-R or CDRW audio discs that have been 
recorded on a computer or CD recorder. The quality of CD-R, CD-RW audio 
discs varies widely which may affect playability. Some factors that affect 
playability:
•  The quality of the disc itself. Generally speaking, CD-R, CD-RW blanks 

from well-renowned companies give better results than unbranded 
ones.

•  The quality of CD-recorder or computer CD re/writer. Some recorders 

and writers produce better results than others.

•  The CD-R and CD-RW were created with high-speed writing. In general, 

the quality of a CD-R or CD-RW is better when produced at a lower 
speed against a higher speed on the same recorder or re/writer. 

The C 516BEE can play MP3/WMA formatted recordings on CD-R or CD-RW 
discs. You may mix any of the file types on the disc. Using the CD 7 remote 
control, one can select through the MP3/WMA folders and files as well as 
start playback through the following steps
1  Load the applicable disc. 
2  Press [FOLDER 

] to select desired folder. Press [ENTER].

3  Press [FILE 

] to select desired file number. You must be at STOP or 

playback mode to access both folders. 

4  Press [ENTER] to start playback. For each file type being played, the 

C 516BEE will display the file type at the VFD and a corresponding icon 
at the VFD.  Information about the Song Title, Album and Artist name, if 
available, will scroll through the VFD during playback.

NOTES
•  The file number is recognized per disc, not per folder – that is, the

The program function enables you to store your favorite tracks from any 
disc in the player memory. When programming a sequence of tracks, the 
C 516BEE must be in STOP mode. Using the CD 7 remote control, enter your 
desired program sequence through the following steps
1  Press [PROGRAM]. The display indicates “P01 T00”.  The “00” in the “T00” 

keeps on blinking, meaning that the player is awaiting the first Program 
entry.  

2  Use the Direct-Entry numeric keypad buttons to enter the first track 

in your planned sequence. Upon entering the track number, the VFD 
will briefly show the total number and total time of the currently 
programmed tracks like “TTL 01  3:25”. 

3  The display will revert to show “P02 T00,” indicating that the player is 

ready for your second program entry.  Upon entering the second track, 
the VFD will again briefly show the total number and total time of the 
currently programmed tracks like  “TTL 02  6:45” – “TTL 02” indicates that 
there are now a total of two programmed tracks and “6:45” is the total 
playback time of both programmed tracks.

4  Repeat steps 2 and 3 to select and store other track numbers in 

memory, up to a maximum of 40 entries. If you attempt to program 
more than 40 tracks or files, “P-FULL” will be displayed in the VFD.

5  Press [PROGRAM] to end or finalize the program – the VFD will show the 

last programmed number and track.

6  Press   to start program playback.

NOTES
•  The procedure for programming MP3/WMA files is the same as above

REVIEW / EDIT PROGRAM LIST
1  Initiate review or edit of your program entries through either of the 

following initial steps
•  If you are still in programming mode, press [PROGRAM].
•  If during program playback, press [STOP] once then [PROGRAM]. 

2  The VFD will show the first Program Number and the corresponding 

“blinking” programmed track.  

3  To change the programmed track of a particular sequence, use the 

Direct-Entry numeric keypad buttons. Press [SKIP 

 or 

] to move 

forward or backward the programmed tracks as well as review the list 
and change if so desired. 

4  If you want to delete a particular program sequence during program 

review, press [DELETE] key.

5  After finalizing your program changes or completing your review, press 

[PROGRAM] again.

PROGRAM PLAYBACK
1  To play the stored program, press [PLAY] while you are in “PROGRAM” 

mode. “PROG” icon will appear in the display, indicating that a stored 
program is being played. During Program Play, the SKIP buttons will 
access only the tracks in the program list. 

2  If you want to play only a portion of a stored program, initiate play and 

press SKIP to jump over the programmed tracks that you don’t want to 
hear. 

STOP OR DELETE PROGRAM
1  To terminate Program play, press [STOP] once. The stored track list 

remains in memory. If you want to play the program again, simply press 
[PLAY]. 

2  To clear the program memory, perform any of the following steps

•  Press [STOP] twice during program playback.
•  Press [OPEN] to open the disc tray.
•  Switch OFF the power.