Справочник Пользователя для Behringer B-Control Fader BCF2000-WH

B-CONTROL FADER BCF2000/B-CONTROL ROTARY BCR2000

2d- Just like 2d, but when the value is 0, no LED lights up.
Bar Bar display: when the value is changed, all LEDs light up

successively (for volume etc.).

Bar-Just like bar display, but when the value is 0, no LED

lights up.

Sprd Spread: When the value is 0, the upper middle LED lights

up; when the value is increased, the LED circle gradually

lights up in both directions (left and right).

Pan In the middle position (value = 64), only the upper middle

LED is on. With lower values, the LED circle lights up

toward the left; with higher values, the LED circle lights

up toward the right (panorama adjustment).

Qual (Quality Q) has the opposite effect from spread: the LED

circle lights up gradually when you decrease the value.

This setting is used for indicating filter quality with

parametric equalizers.

Cut Cutoff is optimal for controlling the cutoff frequency of a

low-pass filter, for example on a synthesizer. When the

value is 0, all LEDs light up. The LEDs go out successively

as you increase the value.

Damp Damping: used for damping filters. When the value is 0,

the outer right LED lights up. If the values are increased,

the LED circle fans out from right to left until all LEDs

light up. This way, increasing damping is best represented

when a value goes up.

Encoder LED display (BCR2000):

(1 digit): Only one LED lights up at a time (standard setting).

1d- The LED circle operates similar to 1d, but when the value

is 0, no LED lights up.

Fader functions (BCF2000):

Move If you move the fader by hand, it sends a new value directly.

In doing so, jumps in the parameter value may occur if the

current value doesnt correspond to the fader position. This

can sometimes happen because in this mode parameter

feedback doesnt cause fader movement.

P-UP Pick up: The fader ignores the parameter feedback.

However, value jumps are avoided because the fader only

sends values if the current value (different from the fader

setting) is exceeded.

Mot

Motor: With parameter feedback, the motorized fader

engages automatically and always indicates the current

value.

Foot controller function:

Move The pedal immediately sends value changes. Value jumps

may result.

P-UP Pick-Up: The foot pedal become active and sends values

only if the set value is exceeded.

SWITCH-type elements:

SWITCH-type control elements have three different modes:

Toggle On, Toggle Off and Increment. Toggle On is similar

to a switching function (e.g. a light switch). Each time you press

the switch, the value sent alternates between the on value (set

by encoder 4) and the off value (set by encoder 5). This setting

is perfect for triggering drum loops from a sampler (press once =

start, press again = stop).

The Toggle Off mode corresponds to a momentary-contact

button, comparable to the switch of an electric door opener. The

on value is sent only as long as the button is pressed. After

releasing the button, the off value is sent. Use this control type

to trigger short sound FX or samples (similar to using a keyboard)

by sending Note On and Offs.

The Increment option only works for buttons, and only on CC,

NRPN and after touch command types. This mode lets you

gradually increase the controller value with each new keystroke.

Set up increment size using encoder 7. If you repeatedly press a

4. OPERATION

button, the value sent will be increased each time by the preset

amount selected here. If increment size is set to 10, values 0,

10, 20, 30 ... 110, 120, 0, 10 and so on will be successively sent

one after another. You can also enter negative values (e.g. -10)

to achieve a gradual decrease in the value. If you use encoders 4

and 5 to delineate the lowest and the highest value that are to be

sent, the values always stay within that range here as well. With

this function, you have the option to use your B-CONTROL to

control software buttons with more than two switch positions.

The value display activated using Push Encoder 8 is identical

for switch and continuous elements. If this value display is active,

the current value is indicated in the four-digit display when you

actuate a control element. The display shows the preset number

again as soon as you release the control element.

4.4 MIDI messages

Program Change:

With the encoders 3 and 4 you can select bank numbers. If a

MIDI device contains more than 128 presets/programs, first a

bank change command has to be sent. Even though this is a

controller command, it has to be sent before the program change

(and is therefore adjustable) since it is linked to the preset change.

If the bank select message is not needed, simply select off.

Encoder 5 selects the program number. If the selected

control element is a control dial (continuous type), the

program number is directly selected when turning the dial.

Pressing the switch directly selects the assigned program

number. This can be useful if you always want to start from

the same preset.
Control Change CC:

A control change consists of a controller number and its

respective value. Encoder 3 sets the controller number. With

buttons, different values can be sent when pressing and releasing

(to be set with encoders 4 and 5). This function is useful if fixed

parameter settings are to be sent.

With faders and control dials (continuous type), the value range

can be determined by using encoders 4 (minimum value) and 5

(maximum value).

Alternatively, you can invert the value scale by assigning

127 as the minimum value and 0 as maximum value

(scale inversion). A classic application is the draw bar

control of virtual or digital organs or organ expanders.

If assigning controller 7 (volume) to the faders of the

BCF2000 this way, the signal becomes quieter when

moving up the fader. Moving down the fader is similar

to moving out the draw bars, and the volume increases.

NRPN:

A NRPN is needed if none of the 127 standardized controller

numbers are available for a certain function.

Encoder 3 selects the parameter number. For assigning mixer

faders, we recommend the high resolution (Absolute 14 bit),

provided that the control hardware/software supports it.
Note:

Of course, a note can only be assigned to one SWITCH element.

The note is set with encoder 3. Note C3 (C key) corresponds with

note number 60. Encoder 4 sets the note velocity (note volume).
Pitch Bend:

Pitch bend is assignable to only one CONTINUOUS element.

Since this is a type of command with its own status byte, selecting

a MIDI channel (Encoder 2) and Range (Encoder 4) is sufficient.
After Touch:

Normally, ALL is selected here. This means that After Touch

affects all notes equally (Channel Pressure). If you want to use

a polyphonic After Touch (Key Pressure), the single note on

which After Touch should have an effect can be selected using

encoder 3. Since this process is only supported by a few tone

generators, channel After Touch will be best most of the time.

When a switch element has been selected, an on and off value