Справочник Пользователя для United States Stove 5040

9

INSTALLATION

E. VERTICALLY INTO EXISTING MASONRY FIREPLACE
NOTE: Follow L-Vent chimney manufacturer’s instructions.
1.  Have the masonry chimney inspected by a qualified chim-

ney sweep or installer to determine its structural condition.

2.  You will need a pipe length equal to the chimney height

     from the hearth. If outside combustion air is to be used, 

     you will need a pipe length equal to the chimney height

     plus 18 inches.
3.  Install a blanking plate and the chimney pipe, and if used

     the outside air pipe, as shown in Figure 12.
4.  Attach the L-Vent adapter, a section of pipe and clean 

out tee, making sure the clean out tee is centered in the 

chimney flue area. Use RTV, metallic tape, and a mini-

mum of three self-taping screws at all joint connections 

to ensure a tight seal.

5.  Position the stove, adhering to the clearances in Figures 

1 & 2.

6.  Measure and build chimney top plate. Cut out holes for    

chimney pipe, and if used the outside air pipe. Install and 

seal with non-hardening mastic to prevent water leakage. 

Install vent cap.

F. INSTALLATION THROUGH SIDE OF MASONRY CHIMNEY
NOTE: Follow L-Vent chimney manufacturer’s instructions.
1.  Position the stove, adhering to the clearances in Figures

     1 & 2. Mark the center of the hole where the pipe is to 

     pierce the masonry chimney.
2.  It will be necessary to break out the masonry around the

     location of the pipe center mark. Use a 4-inch diameter

     hole for 3-inch pipe and 5-inch diameter hole for 4-inch

     pipe. 
3.  Measure and build chimney top plate. Cut out holes for

     chimney pipe, and if used the outside air pipe.

4.  Install the tee on the bottom of the vertical pipe system and

     lower it down the chimney until the center branch of the tee

     is level with the center of the hole in the masonry, as shown 

    in Figure 13.
5.  Install and seal the top plate from step 3 with non-hardening
     mastic. Slip the storm collar over the pipe, and while holding
     the pipe at the proper elevation, affix the collar with a mini-
     mum of three ¼” stainless steel sheet metal screws. Seal all
     joints and seams around the collar.
6.  Connect the horizontal pipe by pushing it through the hole 

     in the masonry and lining it up with the branch in the tee. 

     Push the pipe into the tee while twisting it to lock it into the 

     tee.
7.  If desired, once the horizontal pipe is in place, the space

     between the pipe and masonry may be filled with high-

     temperature grout.

8.  Install the trim collar. An adjustable pipe length and adapter
     may be needed to finish the connection to the stove.

HEARTH

           TOP PLATE

(SEAL TO CHIMNEY TOP

WITH NON-HARDENING

MASTIC)

EXTENSION TO CHIMNEY TOP 

REQUIRED. 

3 OR 4 INCH STAINLESS STEEL

SINGLE WALL PIPE OR FLEX PIPE.

BLANKING PLATE (SEAL WITH 

NON-HARDENING MASTIC).

3 OR 4 INCH STAINLESS STEEL

FLEX PIPE.

OPTIONAL OUTSIDE AIR

CLEAN-OUT-TEE (TYPE L)

OR 90 DEGREE ELBOW

TO

APPLIANCE

6”

 

FROM STOVE 

TO END OF HEARTH

NOTE:

FOLLOW METAL

CHIMNEY INSTALLATION

INSTRUCTIONS

6”

3”

           TOP PLATE

(SEAL TO CHIMNEY TOP

WITH NON-HARDENING

MASTIC)

EXTENSION TO CHIMNEY TOP

REQUIRED.

L-VENT OR OPTIONAL

3 OR 4 INCH STAINLESS STEEL

SINGLE WALL PIPE OR FLEX PIPE.

PIPE ADAPTER

CLEAN-OUT TEE (TYPE L)

TRIM COLLAR

OPTIONAL OUTSIDE AIR

NOTE:

FOLLOW METAL

CHIMNEY INSTALLATION

INSTRUCTIONS

6”

3”