Справочник Пользователя для Qualstar 501440 Rev. G

Скачать
Страница из 89
 
4.5 
Configuring the Fibre Channel Loop ID 
4.5 
Configuring the Fibre Channel Loop ID 
The Id Mode must be configured for either “Soft” or “Fixed” addressing. Using “Soft” 
addressing, the Fibre Channel Option connects to an arbitrated loop using the first 
available AL_PA, scanning from the highest valid address to the lowest. Using “Fixed” 
addressing, the user selects a specific arbitrated loop address (AL_PA) to connect 
with. If the selected address is not available, the Fibre Channel Option will connect 
with the first available address it finds. The use of  “Soft” or “Fixed” addressing is 
based on the user’s installation requirements. 
The Id Mode must be configured for either “Soft” or “Fixed” addressing. Using “Soft” 
addressing, the Fibre Channel Option connects to an arbitrated loop using the first 
available AL_PA, scanning from the highest valid address to the lowest. Using “Fixed” 
addressing, the user selects a specific arbitrated loop address (AL_PA) to connect 
with. If the selected address is not available, the Fibre Channel Option will connect 
with the first available address it finds. The use of  “Soft” or “Fixed” addressing is 
based on the user’s installation requirements. 
Soft addressing can be configured when address conflicts are not likely. If the Fibre 
Channel Option is connected directly to the computer’s HBA (Host Bus Adapter), the 
selection of a specific Loop Id is not usually required. For example, Emulex HBA driv-
ers scan for an available address starting from the low Fibre Channel address range. 
The FCO begins scanning for an available address starting from the high Fibre Chan-
nel address range. This avoids address conflicts and the FCO Loop Id will be assigned 
the same value each time it is restarted. 
Soft addressing can be configured when address conflicts are not likely. If the Fibre 
Channel Option is connected directly to the computer’s HBA (Host Bus Adapter), the 
selection of a specific Loop Id is not usually required. For example, Emulex HBA driv-
ers scan for an available address starting from the low Fibre Channel address range. 
The FCO begins scanning for an available address starting from the high Fibre Chan-
nel address range. This avoids address conflicts and the FCO Loop Id will be assigned 
the same value each time it is restarted. 
Hard addressing should be configured if address conflicts can occur. This can happen 
if the FCO is connected to a Fibre Channel Hub. Since many HBA drivers map the Fi-
bre Channel Loop Id to a SCSI Bus/Target address, this mandates that the Fibre 
Channel Loop Id be very stable, and cannot be allowed to change if the system is sim-
ply restarted. This might happen if soft addressing were used and the Fibre Channel 
Option found its previous address taken. Selecting a fixed address is a way to prevent 
the FCO Loop Id from changing if the system is restarted. 
Hard addressing should be configured if address conflicts can occur. This can happen 
if the FCO is connected to a Fibre Channel Hub. Since many HBA drivers map the Fi-
bre Channel Loop Id to a SCSI Bus/Target address, this mandates that the Fibre 
Channel Loop Id be very stable, and cannot be allowed to change if the system is sim-
ply restarted. This might happen if soft addressing were used and the Fibre Channel 
Option found its previous address taken. Selecting a fixed address is a way to prevent 
the FCO Loop Id from changing if the system is restarted. 
If the computer’s HBA uses the World Wide Port Name (WWPN) convention instead 
of the Loop Id to map to a SCSI Bus/Target/Lun address, the value of the Loop Id is no 
longer important. The WWPN is always unique and consistent under all conditions. In 
the future, all addressing will likely use the WWPN. 
If the computer’s HBA uses the World Wide Port Name (WWPN) convention instead 
of the Loop Id to map to a SCSI Bus/Target/Lun address, the value of the Loop Id is no 
longer important. The WWPN is always unique and consistent under all conditions. In 
the future, all addressing will likely use the WWPN. 
  
Single Bay or one side 
of a Dual Bay Library 
C••••••Fibre•Channel 
•Device Left 
•Device Right 
 L Id Mode 0:   SOFT 
 L Loop Id 0:    nnn 
 L Topology 0:  LOOP 
 R Id Mode 0:   SOFT 
 R Loop Id 0:    nnn 
 R Topology 0:  LOOP 
C••••••Fibre•Channel 
•Device 
 Id Mode 0:     SOFT 
 Loop Id 0:      nnn 
 Topology 0:    LOOP 
  
  
  
  
Dual Bay Library 
with two FCO’s 
  
The 
Configuration\Fibre Channel
 menu panel displays the SCSI device in-
terface and configures the Fibre Channel Interface to host. The menu sets the Fibre 
Channel Option host topology. The “Topology” has two selections, LOOP and FABRIC. 
The LOOP selection configures the Fibre Channel Option for Arbitrated Loop (FC-AL) 
operation. The FABRIC selection configures the Fibre Channel Option for Switch Fab-
ric (FC_SW) operation. If the mode is LOOP, the 
Id Mode
 and 
Loop Id
 entries are 
available. 
The 
Configuration\Fibre Channel
 menu panel displays the SCSI device in-
terface and configures the Fibre Channel Interface to host. The menu sets the Fibre 
Channel Option host topology. The “Topology” has two selections, LOOP and FABRIC. 
The LOOP selection configures the Fibre Channel Option for Arbitrated Loop (FC-AL) 
operation. The FABRIC selection configures the Fibre Channel Option for Switch Fab-
ric (FC_SW) operation. If the mode is LOOP, the 
Id Mode
 and 
Loop Id
 entries are 
available. 
501440 Rev. G
 
501440 Rev. G
 
4-12 
FCO Type A Installation 
 Type A Installation